bora PUXU - Automatic Bridging Function; Cooking Zone Timer

EN
43
Operation
www.bora.com
Setting the time
XX
Select the desired power level:
Command Increase time Decrease time
Swipe
upwards downwards
Tap
(exact to the minute) (exact to the minute)
Tab. 7.3 Setting the time
XO
The timer symbol starts to flash.
Starting the timer
XX
Tap the flashing timer button
XO
The set time starts to count down.
XO
The timer symbol is shown next to the cooking zone.
XO
The operating panel display changes to the standard display
after 2 seconds.
XO
10 seconds before the set time lapses, the system flashes the
remaining time.
XO
In the last 5 seconds of the countdown an acoustic signal can
be heard every second.
Showing the remaining time
The cooking zone timer is active and the time counts down:
XX
Tap the cooking zone
XO
The remaining time is shown in the multi-function display.
Changing active timers
XX
Tap a cooking zone with an active timer
XO
The remaining time is displayed.
XX
Tap the timer button
XO
The timer is stopped.
XO
The remaining time flashes in the display.
XO
The system changes to timer editing mode.
XX
Change the set time (see “Setting the time”).
XX
Confirm the new set time and start the timer (see “Starting
the timer”).
Multi-timer
XX
Tap on a different cooking zone
XO
The additional cooking zone functions are displayed.
XO
If the chosen cooking zone is not yet active (=power level
0
)
a power level can now be set.
XX
Tap the timer button
XO
The time flashes in the 7-segment display above the sliders in
minutes (
0
0
0
).
XO
Now the time can be set and the timer started
(see “Setting the time” and “Starting the timer” respectively).
Switching the timer off early
XX
Tap a cooking zone with an active timer
XO
The remaining time is displayed.
XX
Long press on the timer button
or
XX
long press on the cooking zone with an active timer
XO
The timer is switched off.
XO
The system switches to the standard display.
XO
The cooking zone remains active on the set power level.
Activating the bridging function
XX
Tap both cooking zones at the same time.
XO
The bridging function is now active.
XO
The light that looks like a hyphen goes out and the additional
functions are displayed.
XO
Zone functions apply to the linked cooking zones
(double display).
XO
Both cooking zone indicators show the same power level.
XO
Active additional cooking zone functions are adopted.
XO
Changes to the power level now apply simultaneously to both
cooking zones.
Setting power levels when the bridging function is active.
XX
Tap a cooking zone with an active bridging function.
XX
Set the power level (see Adjusting the power level)
Deactivating the bridging function
XX
Long press on one of the two cooking zones with an active
bridging function
or
XX
tap the cooking zones with an active bridging function
simultaneously.
XO
The bridging function is deactivated.
XO
The hyphen symbol lights up
XO
The power levels are set to 0
XO
If a timer was active, it is deactivated.
XO
If cookware is only detected on one of the two cooking zones,
the bridging function is cancelled after ten seconds and the
corresponding cooking zone is deactivated.
7.5.8 Automatic bridging function
i
If the permanent pan size recognition is switched on (see
Customer menu), the automatic bridging function is also
activated.
7.5.9 Cooking zone timer
i
To be able to activate the timer function, a cooking zone
power level must first be set.
i
The timer function can be used for each cooking zone.
Several timers can be activated at the same time ( multi-
timer).
Activating cooking zone timers
XX
Tap on a cooking zone
XO
The additional cooking zone functions are displayed.
XO
If the chosen cooking zone is not yet active (=power level
0
) a
power level can now be set.
XX
Tap the timer button
XO
The time flashes in the multi-function display above the sliders
in minutes (
0
0
0
).