Canon imagePROGRAF iPF830 User Manual

Setting Item Description, Instructions
GL2
Settings
Line &
Pen
Manag-
er
Smoothing
• If you choose Smooth
ThickenFineLines Select On to print fine lines more distinctly.
AdjustFaintLines If fine lines are printed in colors that do not match the col-
ors of other shapes, selecting Off may help produce the
expected results. However, lines in some colors may ap-
pear broken.
Ln wdth correct Corrects by using a correction value that specifies the pen
width.
You can configure Black/gray and Color for each group.
The specified range is -20 to +20.
Proces-
singOp-
tion
Warning Select On to have any GL2-related warnings displayed.
On-the-Fly Selecting On will start printing jobs sooner if you are print-
ing only HP RTL print jobs and printing would not start un-
til later. However, images may be incomplete in some ca-
ses, so be sure to check the printing results.
Detect img size Sets the method of deciding the region to output in order
to print efficiently while avoiding missing images.
If Off is selected and the data contains image range infor-
mation, the image range information is followed.
If Off is selected and the data does not contain image
range information, a size with the maximum roll paper
width of the printer for the width and 1.5 times the maxi-
mum roll paper width for the length is used.
If Command priority is selected and the data contains
image range information, the image range information is
followed.
If Command priority is selected and the data does not
contain image range information, the detected minimum
image area is used.
If Detected size is selected, the detected minimum image
area is used.
GL2 Set Print Print GL2 settings information.
Inter-
face
Setup
EOP Timer Specify the timeout period before cancellation of print jobs
that cannot be received by the printer.
TCP/IP IPv4 IPv4 Mode Choose whether the printer IP address is configured auto-
matically or a static IP address is entered manually.
Proto-
col
DHCP Specify the protocol used to configure the IP address au-
tomatically.
BOOTP
RARP
IPv4
Settings
IP Address Specify the printer network information when using a stat-
ic IP address.
Enter the IP address assigned to the printer, as well as
the network subnet mask and default gateway.
The value that was automatically configured is displayed if
you have set IPv4 Mode to Automatic.
Subnet Mask
Default G/W
DNS
Settings
DNS Dync update Specify whether DNS server registration is updated auto-
matically.
Pri. DNS SrvAddr Specify the DNS server address.
Sec. DNS SrvAddr
iPF830 Menu Settings
User's Guide
Control Panel Printer Menu
449

Canon imagePROGRAF iPF830 Specifications

General

Color	Yes
Printing colors	Black, Cyan, Magenta, Matte black, Yellow
Print technology	Inkjet
Maximum resolution	2400 x 1200 DPI
Number of print cartridges	5
Page description languages	GARO, HP-GL/2, HP-RTL
Minimum line width	0.02 mm
Number of power supply units	1
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3az
Media thickness	0.07 - 0.8 mm
Maximum print size	A0 (841 x 1189 mm)
Maximum roll length	18 m
Media width (sheets)	1117.6 mm
Maximum roll diameter	150 mm
ISO A-series sizes (A0...A9)	A0, A1
JIS B-series sizes (B0...B9)	B0, B2
Display	LCD
Product color	Black, Grey
Storage media	HDD
Internal storage capacity	320 GB
Sound power level (standby)	35 dB
Sound pressure level (printing)	52 dB
USB connector	USB Type-A
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet interface type	Gigabit Ethernet
Power supply	190 W
Power consumption (off)	0.5 W
Power consumption (standby)	5 W
Operating temperature (T-T)	15 - 30 °C
Operating relative humidity (H-H)	10 - 80 %
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	975 mm
Width	1893 mm
Height	1144 mm