Need help?Do you have a question about the Convotherm OEB Series and is the answer not in the manual?
General| Category | Commercial Food Equipment |
|---|---|
| Series | OEB |
| Cooking Modes | Convection, Steam, Combination |
| Capacity | 6-20 levels |
| Water Connection | Required |
| Dimensions (WxDxH) | Varies by model |
| Weight | Varies by model |
| Temperature Range | 85°F - 482°F (30°C - 250°C) |
Main section covering service documentation for CONVOTHERM appliances.
Lists the various service documents and handbooks available.
Form for acknowledging receipt and copyright of the service folder.
Explains the meaning of various symbols used for safety advice.
Provides main telephone numbers for CONVOTHERM service and sales.
Details hazardous warnings related to gas, electricity, and burns.
Provides safety instructions for lifting, moving, and working on the unit.
Information on shipping practices and commitment to environmental protection.
Explains the closed system for steam and heat circulation with diagrams.
Details basic settings, focusing on standby mode for steam generator units.
Explains the function and components of the outgoing water cooling system.
Describes the demoisturizing process in a closed system for Crisp & Tasty.
Details the automatic and manual draining and rinsing procedures for the steam generator.
Explains the optional automatic cleaning process, its duration, and buzzer signals.
Illustrates the water flow plan within the unit with detailed component labeling.
Explains the function of the door safety switch and its impact on motor and heating elements.
Details various electronic safety switches and their functions in different unit types.
Describes electrical safety switches like capillary probes and their functions.
Explains the process of steaming at 100°C in units with steam generators.
Details the steaming process under 100°C, applicable to steam generator units.
Explains the Superheated Steam program in units with steam generators.
Describes the Convection programme in units with steam generators, including preheating.
Explains the Regeneration program, a combination of steam and convection heating.
Details Delta-T cooking, emphasizing the relationship between oven and core temperature.
Explains the two phases of the Cook & Hold program for gentle cooking and warm holding.
Provides an overview chart of processes and probes used in units with steam generators.
Highlights features of the gas technology, including burner, performance, and emissions.
Describes key components of the gas technology, such as burner and gas valve.
Explains the principle and safety of the Venturi-High performance burner system.
Details how to access and use the service programme for diagnostics and settings.
Lists and explains various service numbers for accessing appliance parameters and diagnostics.
Explains how to test various outputs and identify defects using service numbers d04-d24.
Lists possible error messages, their descriptions, and possible causes or remedies.
Explains how to operate the appliance in an emergency mode when errors occur.
Provides a diagram showing the assignment of the control module (CM) in OEB and OES units.
Details the connections and assignments for the Gas module (GM) in OGB units.
Introduces the basic settings accessible via the "easy Touch" interface.
Guides through the initial setup of language, date, time, and sounds.
Explains how to access and utilize the diagnosis system within the service programme.
Provides a schedule for cleaning and descaling intervals based on usage.
Details the automatic steam generator flushing procedure and its importance.
Provides information and safety advice for daily cleaning of the oven.
Explains the operation instructions and safety for half-automatic oven cleaning.
Details safety and operation for the optional CONVOClean system.
Covers cleaning of hygenic plug-in gaskets and ventilation areas.
Provides information, safety, and attention points regarding descaling.
Details oven descaling procedures for OES/OGS units, including water quality.
Explains steam generator cleaning and descaling for OEB/OGB units.
Covers descaling of various unit parts and components, including removal instructions.
Lists and describes CONVOTHERM cleaning and care products.
Outlines the importance of maintenance and general points for ensuring proper functioning.
Provides a checklist for verifying correct installation according to handbook standards.
Details visual checks for tightness and condition of electrical connections and terminals.
Lists visual checks for components like door latch, hinges, and panels.
Checklist for installers and customers to ensure proper installation of the unit.
Key safety points and applicable uses to inform the user about.
Introduction to troubleshooting electronic issues and error messages for easyTouch controls.
Lists specific error messages, descriptions, and possible causes for electronic faults.
Explains how error codes are constructed using variants for fan motor issues.
Lists general defects and their possible causes or remedies.
Details troubleshooting steps for steam generator related issues and error messages.
Lists possible causes and remedies for condenser-related defects and errors.
Provides troubleshooting steps for motor-related issues, including fan malfunction.
Explains issues related to the safety temperature limiter for hot air heaters.
Addresses issues related to the EasyTouch control display and software.
Explains how to interpret LEDs on supply, control, and operating modules for troubleshooting.
Details the LEDs on the Gas module (GM) and their diagnostic meanings.
Explains troubleshooting using LEDs on frequency converters (SAWI and ALTIVAR).
Provides instructions for removing and installing the Operating Module (BM).
Details the procedure for removing and installing the Control Module (SM).
Explains how to replace the Arrangement module, its function, and LEDs.
Guides through the removal and installation of the Gas module (GM).
Shows the location of LEDs on the Gas, Control, and Operating modules for self-testing.
Details software version compatibility and how to check current software levels.
Provides step-by-step instructions for updating software via PC or laptop.
Covers SD card preparation, including formatting to FAT file system.
Details the sequence for performing a software update using the SD card black box.
Explains the automatic update process for the EasyTouch operating module from version 1.3.0.0.
Guides on manually updating the operating module to software version 1.3.0.0.
Details the process for updating the control module software to version 1.3.0.0.
Provides instructions for draining the steam generator and replacing the drain pump.
Illustrates the location and replacement of various probes and safety thermostats.
Details the placement of safety thermostats above the unit ceiling and behind the motor.
Explains the replacement of the core temperature probe (CTC) with a stuffing box assembly.
Guides through removing and replacing the water level probe, including checks.
Details the procedure for replacing the immersion heating element in OEB units.
Provides instructions for installing and removing the motor and fan wheel.
Covers troubleshooting and adjustment of the pressure switch for the cleaning system.
Explains how to activate and deactivate the dummy operation mode for P3 units.
Guides through the process of removing and installing the condenser.
Details the removal and installation procedures for the door latch and contact switch.
Explains how to use the water analysis unit to measure water conductivity.
Instructions for sealing the corners of the door gasket frame on table units.
Explains the cause of glass corrosion and how to solve the problem.
Guides through the removal and installation of the inner door on table units.
Details the procedure for replacing the outer door on table and standing units.
Instructions for mounting the drip tray for overflow protection.
Provides instructions for removing and replacing the convection heater.
Details the step-by-step process for removing and replacing the convection heat exchanger.
Guides on how to remove and replace burners, including safety checks.
Provides safety advice and information before adjusting gas valves.
Explains how to check the air panel and its number code against chart information.
Guides on checking and potentially replacing the gas panel based on gas type.
Details how to adjust MIN, MAX, and START speeds for burner blowers in the service program.
Explains how to start the burner and measure gas exhaust values at MAX speed.
Guides on adjusting the burner's MIN speed using service points.
Instructions on checking all connections for gas tightness before unit operation.
Covers sealing adjustment for the gas valve cover and Venturi screw, reconnecting the HL2 burner.
Provides an overview of the disappearing door replacement and adjustment process.
Details how to adjust the disappearing door, including gap and sealing.
Instructions for removing and replacing rollers for the slot panel.
Provides a summary of the service manual chapters for OEB/OES/OGB/OGS/Mini-world.
Describes the control panel components and functions for ST7000 easyTouch controls.
Explains how to access the basic settings service level via the "easy Touch" interface.
Details the initial settings required when first installing the appliance.
Guides on navigating and using the diagnosis system within the service program.
Introduction to troubleshooting electronic issues and error messages for easyTouch controls.
Lists specific error messages, descriptions, and possible causes for electronic faults.
Explains how error codes are constructed using variants for fan motor issues.
Explains how to use LEDs on supply, control, and operating modules for troubleshooting.
Details the LEDs on the Gas module (GM) and their diagnostic meanings.
Explains troubleshooting using LEDs on frequency converters (SAWI and ALTIVAR).
Guides on disassembling and assembling control electronics for mini-world appliances.
Details how to replace the ST7000 operating module, including safety precautions.
Provides instructions for replacing the control module (CM) ST5010.
Guides on replacing the supply module (SM), including safety and check procedures.
Shows the location of LEDs on control and operating modules for self-testing.
Explains the automatic update process for the EasyTouch operating module from version 1.3.0.0.
Guides on manually updating the operating module to software version 1.3.0.0.
Details the process for updating the control module software to version 1.3.0.0.
Lists spare parts for the EasyTouch ST7000, including part numbers.
To Next Page