EasyManuals Logo

Danfoss VLT AQUA Drive FC 202 Programming Guide

Danfoss VLT AQUA Drive FC 202
294 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #243 background imageLoading...
Page #243 background image
3.25.6 29-6* Flow Meter
VLT
®
AQUA Drive FC 202 can measure the ow in the
system. Irrigation applications is the most common use
case for parameters in this parameter group. The
functionality allows to:
Measure the ow in the system.
Calculate the water volume pumped for a period
of time.
React on ow conditions (for example, low ow
rate).
Control the system using the pumped water
volume calculated by the frequency converter (for
example, stop pumping when a certain amount
of water is pumped, cyclic pumping of water
volumes).
Utilize the output signal of an external ow meter
that is connected to an input of the frequency
converter.
Inputs and supported signal types
The ow meter feature can use and scale the output
signals of commonly used ow meters. The feature
supports the following signal types:
Current: 0/4–20 mA.
Voltage: 0–10 V.
Pulse signal (for example: paddle wheel ow
meters).
Congure the scaling of the ow meter signal received as
input via the available parameters for the input congu-
ration (parameters in parameter group 6-** Analog In/Out,
or 5-5* Pulse Input). The ow meter feature also supports
inputs of hardware options.
Volume counters
The ow meter feature uses 2 dierent counters for storing
the calculated volume of pumped water:
Parameter 29-66 Actual Volume: See the volume of
water pumped since the last counter reset.
Parameter 29-65 Totalized Volume: See the volume
of water pumped since the last counter reset. Use
this parameter for the total volume of water
pumped.
The 2 counters can have dierent units. Use
parameter 29-66 Actual Volume for shorter periods of time.
Each parameter can be reset individually in 1 of the
following ways:
Using parameter 29-67 Reset Totalized Volume or
parameter 29-68 Reset Actual Volume.
Using a digital input.
Using an action of the smart logic controller.
Reading the data
The measured data is available via readout parameters:
Parameter 29-65 Totalized Volume.
Parameter 29-66 Actual Volume.
Parameter 29-69 Flow.
To show the readout parameters on the LCP, congure the
display lines. Comparator operands can use the data from
readout parameters as conditions for SLC, and as triggers
for actions. The measured ow can also be used as input
for the feedback.
NOTICE
This software feature has not been designed as being
part of a calibrated measurement system. The overall
accuracy also depends on external factors such as ow
conditions and used ow meter. See the design guide for
details about analog and digital inputs of the frequency
converter.
Examples
A sequence of SLC is triggered (or stopped) after
a specic amount of water is pumped.
The frequency converter performs 1 or more
actions and resets the volume counters within a
sequence of SLC.
An alert shows up after a specic amount of
water is pumped.
29-60 Flow Meter Monitor
Enable the ow meter monitor.
Option: Function:
[0] * Disabled
[1] Enabled
[2] Enabled While Running Enable the monitor only when the
connected pump is running.
29-61 Flow Meter Source
Select the source for the ow meter signal. Available options
depend on the hardware conguration.
Option: Function:
[0] * Analog Input 53
[1] Analog Input 54
[2] Analog Input X30/11
[3] Analog Input X30/12
[4] Analog Input X42/1
[5] Analog Input X42/3
[6] Analog Input X42/5
[7] Analog Input X48/2
[8] Pulse Input 29
[9] Pulse Input 33
[10] Bus Feedback 1
[11] Bus Feedback 2
[12] Bus Feedback 3
Parameter Description Programming Guide
MG20OB02 Danfoss A/S © 05/2018 All rights reserved. 241
3 3

Table of Contents

Other manuals for Danfoss VLT AQUA Drive FC 202

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Danfoss VLT AQUA Drive FC 202 and is the answer not in the manual?

Danfoss VLT AQUA Drive FC 202 Specifications

General IconGeneral
BrandDanfoss
ModelVLT AQUA Drive FC 202
CategoryDC Drives
LanguageEnglish

Related product manuals