Danfoss VLT AutomationDrive Design Guide

O
Ordering
From Type Code............................................................................... 95
Numbers.............................................................................................. 95
Numbers: Du/dt Filters, 380-480/500V AC........................... 116
Numbers: Du/dt Filters, 525-690V AC......................................... 2
Numbers: Harmonic Filters........................................................ 113
Numbers: High Power Kits......................................................... 101
Numbers: Options And Accessories.......................................... 99
Numbers: Sine Wave Filter Modules, 200-500 VAC........... 115
Numbers: Sine-Wave Filter Modules, 525-690 VAC............... 2
Output Performance (U, V, W).......................................................... 85
P
Parameter Values............................................................................... 267
PELV
PELV.................................................................................................... 231
- Protective Extra Low Voltage.................................................... 41
Planning The Installation Site........................................................ 121
Point Of Common Coupling.......................................................... 225
Power
Connections.................................................................................... 169
Connections 12-Pulse Drives..................................................... 180
Process PID Control............................................................................. 32
Profibus................................................................................................ 7, 99
Programming Of Torque Limit And Stop.................................. 233
Protection
Protection.................................................................................... 14, 41
And Features...................................................................................... 86
Mode..................................................................................................... 12
Protocol Overview............................................................................. 256
Pulse/Encoder Inputs.......................................................................... 87
R
Radiated Emission................................................................................ 38
Rated Motor Speed................................................................................ 8
RCD
RCD.......................................................................................................... 9
(Residual Current Device)........................................................... 253
Receiving The Frequency Converter........................................... 121
Reference
Reference.......................................................................................... 228
Limits.................................................................................................... 24
Relay
Connection...................................................................................... 168
Outputs................................................................................................ 88
Removal Of Knockouts For Extra Cables.................................... 158
Residual Current Device.................................................................. 226
RFI Switch.............................................................................................. 224
Rise Time.................................................................................................. 91
S
Safe
Stop....................................................................................................... 51
Stop + Pilz Relay............................................................................. 254
Safety
Earth Connection........................................................................... 220
Precautions........................................................................................ 11
Requirements Of Mechanical Installation............................ 117
Scaling
Of Analog And Pulse References And Feedback.................. 25
Of Preset References And Bus References.............................. 25
Screened Control Cables................................................................. 224
Screened/armoured....................................................... 160, 214, 217
Screening Of Cables:................................................................ 169, 182
Serial Communication............................................................... 224, 89
Short
Circuit (Motor Phase – Phase)...................................................... 49
Circuit Ratio..................................................................................... 225
Side-by-side Installation.................................................................. 120
Sine-wave
Filter....................................................................... 163, 170, 182, 253
Filters.................................................................................................. 253
Software Versions.............................................................................. 100
Space
Space.................................................................................................. 133
Heaters And Thermostat............................................................. 253
Spare Parts............................................................................................ 100
Special Conditions............................................................................... 94
Speed
PID.................................................................................................. 17, 19
PID Control......................................................................................... 30
Reference.......................................................................................... 228
Static Overload In VVCplus Mode................................................... 49
Status
Word................................................................................................... 269
Word According To PROFIdrive Profile (STW)..................... 272
Surroundings......................................................................................... 89
Switches S201, S202, And S801..................................................... 211
Switching
Frequency:.............................................................................. 170, 182
On The Output.................................................................................. 49
Symbols...................................................................................................... 7
Synchronous Motor Speed.................................................................. 8
T
Terminal
Locations.......................................................................................... 137
Locations - Frame Size D.................................................................. 3
The
EMC Directive (2004/108/EC)....................................................... 13
Low-voltage Directive (2006/95/EC)......................................... 13
Machinery Directive (2006/42/EC)............................................. 12
Index FC 300 Design Guide
MG.33.BD.02 - VLT
®
is a registered Danfoss trademark 277

Danfoss VLT AutomationDrive Specifications

General

Supply Voltage	3 x 200-240 V ±10% 3 x 380-500 V ±10% 3 x 525-600 V ±10%
Enclosure	IP20
Output Power Range	0.25 kW - 1.5 MW
Communication Protocols	Modbus RTU
Protection Features	Overcurrent, Overvoltage, Undervoltage, Short circuit, Ground fault, Motor overload
Ambient Temperature Range	-10°C to +50°C (14°F to 122°F)