Datalogic Gryphon I GFS4400 - Rs-232 Only Interface

To Next Page

To Previous Page

Product Reference Guide

RS-232 ONLY INTERFACE

BAUD RATE on page 26

DATA BITS on page 27

STOP BITS on page 27

PARITY on page 28

HANDSHAKING CONTROL on page 29

Use the programming bar codes in this section if modific

ations to the standard RS-232

interface settings are necessary to meet your system’s requirements. Additional settings

which apply to both the RS-232 and USB interfaces are available in the next section, "RS-

232/USB-Com Interfaces" starting on page 30.

Reference Appendix C, Standard Defaults for a listing of standard factory settings.

Main Page

Default Chapter1
- Product Reference Guide1
- Table of Contents3
Introduction11
- About this Manual11
  - Overview11
  - Manual Conventions12
- References12
- Technical Support12
- About the Reader13
- Programming the Reader13
  - Configuration Methods13
Setup15
- Unpacking15
- Setting up the Reader15
- Attaching Reader to Host16
- Interface Selection17
- Custom Configuration Settings20
Configuration Using Bar Codes23
- Configuration Parameters23
  - Global Interface Features25
    - Host Commands - Obey/Ignore25
- Rs-232 Only Interface27
- RS-232/USB-Com Interfaces32
- USB Keyboard Settings39
- USB-OEM Interface49
- Data Format53
- Global Prefix/Suffix54
- Global AIM ID55
  - Set AIM ID Individually for GS1-12857
- Label ID58
  - Label ID: Pre-Loaded Sets58
  - Individually Set Label ID59
- Digital Output71
- Reading Parameters75
  - Double Read Timeout76
  - Led and Beeper Indicators77
- Symbologies95
- 1D Code Selection95
Code 39 Pzn127
- Code 39 PZN Enable/Disable127
Code128
- Code 128 Enable/Disable128
- Expand Code 128 to Code 39128
- Code 128 Check Character Transmission129
- Code 128 Function Character Transmission129
- Code 128 Sub-Code Exchange Transmission130
- Code 128 Quiet Zones130
- Code 128 Length Control131
- Code 128 Set Length 1132
- Code 128 Set Length 2133
Gs1-128134
- GS1-128 Enable134
- GS1-128 2D Component134
Code Isbt 128135
- ISBT 128 Concatenation135
- ISBT 128 Force Concatenation135
- ISBT 128 Concatenation Mode136
- ISBT 128 Dynamic Concatenation Timeout137
- ISBT 128 Advanced Concatenation Options137
Interleaved 2 of 5 (I 2 of 5)138
- I 2 of 5 Enable/Disable138
- I 2 of 5 Check Character Calculation139
- I 2 of 5 Check Character Transmission140
- I 2 of 5 Length Control140
- I 2 of 5 Set Length 1141
- I 2 of 5 Set Length 2142
Interleaved 2 of 5 Cip Hr143
- Interleaved 2 of 5 CIP HR Enable/Disable143
Follett 2 of 5143
- Follett 2 of 5 Enable/Disable143
Standard 2 of 5144
- Standard 2 of 5 Enable/Disable144
- Standard 2 of 5 Check Character Calculation144
- Standard 2 of 5 Check Character Transmission145
- Standard 2 of 5 Length Control145
- Standard 2 of 5 Set Length 1146
- Standard 2 of 5 Set Length 2146
Industrial 2 of 5148
- Industrial 2 of 5 Enable/Disable148
- Industrial 2 of 5 Check Character Calculation148
- Industrial 2 of 5 Check Character Transmission149
- Industrial 2 of 5 Length Control149
- Industrial 2 of 5 Set Length 1150
- Industrial 2 of 5 Set Length 2150
Code Iata152
- IATA Enable/Disable152
- IATA Check Character Transmission152
Codabar153
- Codabar Enable/Disable153
- Codabar Check Character Calculation153
- Codabar Check Character Transmission154
- Codabar Start/Stop Character Transmission154
- Codabar Start/Stop Character Set155
- Codabar Start/Stop Character Match155
- Codabar Quiet Zones156
- Codabar Length Control156
- Codabar Set Length 1157
- Codabar Set Length 2158
Abc Codabar159
- ABC Codabar Enable/Disable159
- ABC Codabar Concatenation Mode159
- ABC Codabar Dynamic Concatenation Timeout160
- ABC Codabar Force Concatenation161
- Code 11162
- 2D Symbologies187
- 2D Global Features187
- Aztec Code190
  - Aztec Code Enable / Disable190
  - Aztec Code Length Control190
    - Aztec Code Set Length 1191
    - Aztec Code Set Length 2192
- China Sensible Code193
  - China Sensible Code Enable / Disable193
  - China Sensible Code Length Control193
    - China Sensible Code Set Length 1194
    - China Sensible Code Set Length 2195
- Data Matrix196
- Maxicode199
- Pdf417202
  - PDF417 Enable / Disable202
  - PDF417 Length Control202
    - PDF417 Set Length 1203
    - PDF417 Set Length 2204
- Micro PDF417205
- QR Code208
  - QR Code Enable / Disable208
  - QR Code Length Control208
    - QR Code Set Length 1209
    - QR Code Set Length 2210
- Micro QR Code211
  - Micro QR Code Enable/Disable211
  - Micro QR Code Length Control211
    - Micro QR Code Set Length 1212
    - Micro QR Code Set Length 2213
- UCC Composite214
  - UCC Composite Enable / Disable214
  - UCC Optional Composite Timer215
- Postal Code Selection216
  - Postnet BB Control217
Software Configuration Strings219
- Command Syntax220
  - Serial Configuration Strings222
References245
- RS-232 Parameters246
- Symbologies255
  - Set Length255
- Data Editing256
- Digital Output267
- Reading Parameters268
  - Double Read Timeout268
  - Good Read LED Duration269
- Scanning Features270
Technical Specifications277
- Imager Labeling282
  - Aiming System282
- LED and Beeper Indications283
  - Button and LED Status283
  - Indicators283
- Error Codes285
Aimer Calibration287
Standard Defaults291
- QR Code Set Length 1301
Sample Bar Codes303
- Gs1 Databar305
  - D Bar Codes306
  - Composite Codes306
Keypad307
Reserved Characters309
Scancode Tables311
- Control Character Emulation311
  - Single Press and Release Keys311
- Interface Type PC at PS/2, USB-Keyboard or USB-Keyboard for APPLE312
- Interface Type PC at PS/2 Alt Mode or USB-Keyboard Alt Mode314
- Digital Interface316
- Ibm31Xx 102-Key317
- Ibm Xt318
- Microsoft Windows Codepage 1252319
  - Ascii Chart323

Datalogic Gryphon I GFS4400 - Rs-232 Only Interface

Table of Contents

Other manuals for Datalogic Gryphon I GFS4400

Related product manuals