To Next Page

To Previous Page

RS-232 Only Interface Enter/Exit Programming Mode

Product Reference Guide

Data Bits

This parameter allows the reader to interface with devices requiring a 7-bit or 8-bit ASCII

protocol for sending and receiving data.

$CR2DA00(CR)

7 Data Bits

$CR2DA01(CR)

8 Data Bits

DEFAULT

Stop Bits

Set the number of stop bits to match host device requirements. See page 244 for more

information on this feature.

DEFAULT

$CR2ST00(CR)

1 Stop Bit

$CR2ST01(CR)

2 Stop Bits

Default Chapter1
- Product Reference Guide1
- Table of Contents3
Introduction11
- About this Manual11
  - Overview11
  - Manual Conventions12
- References12
- Technical Support12
- About the Reader13
- Programming the Reader13
  - Configuration Methods13
Setup15
- Unpacking15
- Setting up the Reader15
- Attaching Reader to Host16
- Interface Selection17
- Custom Configuration Settings20
Configuration Using Bar Codes23
- Configuration Parameters23
  - Global Interface Features25
    - Host Commands - Obey/Ignore25
- Rs-232 Only Interface27
- RS-232/USB-Com Interfaces32
- USB Keyboard Settings39
- USB-OEM Interface49
- Data Format53
- Global Prefix/Suffix54
- Global AIM ID55
  - Set AIM ID Individually for GS1-12857
- Label ID58
  - Label ID: Pre-Loaded Sets58
  - Individually Set Label ID59
- Digital Output71
- Reading Parameters75
  - Double Read Timeout76
  - Led and Beeper Indicators77
- Symbologies95
- 1D Code Selection95
Code 39 Pzn127
- Code 39 PZN Enable/Disable127
Code128
- Code 128 Enable/Disable128
- Expand Code 128 to Code 39128
- Code 128 Check Character Transmission129
- Code 128 Function Character Transmission129
- Code 128 Sub-Code Exchange Transmission130
- Code 128 Quiet Zones130
- Code 128 Length Control131
- Code 128 Set Length 1132
- Code 128 Set Length 2133
Gs1-128134
- GS1-128 Enable134
- GS1-128 2D Component134
Code Isbt 128135
- ISBT 128 Concatenation135
- ISBT 128 Force Concatenation135
- ISBT 128 Concatenation Mode136
- ISBT 128 Dynamic Concatenation Timeout137
- ISBT 128 Advanced Concatenation Options137
Interleaved 2 of 5 (I 2 of 5)138
- I 2 of 5 Enable/Disable138
- I 2 of 5 Check Character Calculation139
- I 2 of 5 Check Character Transmission140
- I 2 of 5 Length Control140
- I 2 of 5 Set Length 1141
- I 2 of 5 Set Length 2142
Interleaved 2 of 5 Cip Hr143
- Interleaved 2 of 5 CIP HR Enable/Disable143
Follett 2 of 5143
- Follett 2 of 5 Enable/Disable143
Standard 2 of 5144
- Standard 2 of 5 Enable/Disable144
- Standard 2 of 5 Check Character Calculation144
- Standard 2 of 5 Check Character Transmission145
- Standard 2 of 5 Length Control145
- Standard 2 of 5 Set Length 1146
- Standard 2 of 5 Set Length 2146
Industrial 2 of 5148
- Industrial 2 of 5 Enable/Disable148
- Industrial 2 of 5 Check Character Calculation148
- Industrial 2 of 5 Check Character Transmission149
- Industrial 2 of 5 Length Control149
- Industrial 2 of 5 Set Length 1150
- Industrial 2 of 5 Set Length 2150
Code Iata152
- IATA Enable/Disable152
- IATA Check Character Transmission152
Codabar153
- Codabar Enable/Disable153
- Codabar Check Character Calculation153
- Codabar Check Character Transmission154
- Codabar Start/Stop Character Transmission154
- Codabar Start/Stop Character Set155
- Codabar Start/Stop Character Match155
- Codabar Quiet Zones156
- Codabar Length Control156
- Codabar Set Length 1157
- Codabar Set Length 2158
Abc Codabar159
- ABC Codabar Enable/Disable159
- ABC Codabar Concatenation Mode159
- ABC Codabar Dynamic Concatenation Timeout160
- ABC Codabar Force Concatenation161
- Code 11162
- 2D Symbologies187
- 2D Global Features187
- Aztec Code190
  - Aztec Code Enable / Disable190
  - Aztec Code Length Control190
    - Aztec Code Set Length 1191
    - Aztec Code Set Length 2192
- China Sensible Code193
  - China Sensible Code Enable / Disable193
  - China Sensible Code Length Control193
    - China Sensible Code Set Length 1194
    - China Sensible Code Set Length 2195
- Data Matrix196
- Maxicode199
- Pdf417202
  - PDF417 Enable / Disable202
  - PDF417 Length Control202
    - PDF417 Set Length 1203
    - PDF417 Set Length 2204
- Micro PDF417205
- QR Code208
  - QR Code Enable / Disable208
  - QR Code Length Control208
    - QR Code Set Length 1209
    - QR Code Set Length 2210
- Micro QR Code211
  - Micro QR Code Enable/Disable211
  - Micro QR Code Length Control211
    - Micro QR Code Set Length 1212
    - Micro QR Code Set Length 2213
- UCC Composite214
  - UCC Composite Enable / Disable214
  - UCC Optional Composite Timer215
- Postal Code Selection216
  - Postnet BB Control217
Software Configuration Strings219
- Command Syntax220
  - Serial Configuration Strings222
References245
- RS-232 Parameters246
- Symbologies255
  - Set Length255
- Data Editing256
- Digital Output267
- Reading Parameters268
  - Double Read Timeout268
  - Good Read LED Duration269
- Scanning Features270
Technical Specifications277
- Imager Labeling282
  - Aiming System282
- LED and Beeper Indications283
  - Button and LED Status283
  - Indicators283
- Error Codes285
Aimer Calibration287
Standard Defaults291
- QR Code Set Length 1301
Sample Bar Codes303
- Gs1 Databar305
  - D Bar Codes306
  - Composite Codes306
Keypad307
Reserved Characters309
Scancode Tables311
- Control Character Emulation311
  - Single Press and Release Keys311
- Interface Type PC at PS/2, USB-Keyboard or USB-Keyboard for APPLE312
- Interface Type PC at PS/2 Alt Mode or USB-Keyboard Alt Mode314
- Digital Interface316
- Ibm31Xx 102-Key317
- Ibm Xt318
- Microsoft Windows Codepage 1252319
  - Ascii Chart323

Brand	Datalogic
Model	Gryphon I GFS4400
Category	Barcode Reader
Language	English

Datalogic Gryphon I GFS4400 User Manual

Table of Contents

Other manuals for Datalogic Gryphon I GFS4400

Questions and Answers:

Datalogic Gryphon I GFS4400 Specifications

Related product manuals