DURKOPP ADLER M-TYPE 667

92 pages

To Previous Page

To Previous Page

Loading...

DÜRKOPP ADLER AG

Potsdamer Str. 190

33719 Bielefeld

Germany

Phone: +49 (0) 521 925 00

Email: service@duerkopp-adler.com

www.duerkopp-adler.com

Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany

© Dürkopp Adler AG - Service Instructions - 0791 667640 EN - 00.0 - 04/2016

Table of Contents

Default Chapter3
- Table of Contents3
1 About These Service Instructions5
- Scope of the Service Instructions5
- Representation Conventions - Symbols and Characters5
- Other Documents6
- Liability6
2 Safety7
- Basic Safety Instructions7
- Signal Words and Symbols Used in Warnings8
3 Working Basis11
- Order of the Settings11
- Cable Routing11
- Removing the Covers12
- Tilting and Erecting the Machine Head12
- Removing and Placing the Arm Cover13
- Removing and Placing the Head Cover14
- Removing and Placing the Valve Cover15
- Removing and Installing the Throat Plate16
- Removing and Installing the Feed Dog17
- Flats on Shafts18
- Locking the Sewing Machine in Place18
- Setting the Handwheel into Position20
4 Positioning the Arm Shaft21
5 Setting the Handwheel Scale23
6 Positioning the Toothed Belt Wheels25
- Setting the Upper Toothed Belt Wheel25
- Setting the Lower Toothed Belt Wheel27
7 Setting the Stitch Length Adjusting Wheels29
- Setting the Upper Stitch Length Adjusting Wheel30
- Setting the Lower Stitch Length Adjusting Wheel32
- Setting the Stitch Length Limit34
- Setting the Eccentric for the Forward and Backward Stitches35
8 Setting the Feed Dog37
- Setting the Feed Dog Position37
- Moving the Feed Dog38
- Moving the Feed Dog Carrier39
- Setting the Feed Dog Movement40
- Setting the Feed Movement40
- Setting the Feed Dog Height at Top Dead Center41
- Setting the Stroke Movement42
9 Aligning the Needle Bar Linkage45
- Moving the Needle Bar Linkage Sideways45
- Aligning the Needle Bar Linkage in the Sewing Direction47
10 Position of the Hook and Needle49
- Setting the Hook Side Clearance49
- Setting the Loop Stroke Position51
- Setting the Needle Bar Height53
11 Sewing Feet55
- Setting an Even Sewing Foot Stroke56
- Setting the Stroke Movement for the Feeding Foot57
- Setting the Sewing Foot Pressure59
- Setting the Sewing Foot Lifting Height60
12 Setting the Needle Thread Tension61
- Setting the Needle Thread Regulator61
- Setting the Thread Tensioning Spring62
13 Winder63
- Setting the Winder63
- Setting the Hook Thread Guide66
14 Thread Cutter67
- Setting the Control Cam Position67
- Setting the Armature of the Thread Cutter Magnet68
- Setting the Position of the Thread-Pulling Knife69
- Setting the Cutting Pressure70
15 Setting the Potentiometer73
16 Maintenance75
- Cleaning76
- Cleaning the Machine76
- Cleaning the Motor Fan Mesh77
- Lubricating78
- Lubricating the Machine Head79
- Lubricating the Hook80
- Servicing the Pneumatic System81
- Setting the Operating Pressure81
- Draining the Water Condensation82
- Cleaning the Filter Element83
- Servicing Specific Components84
- Parts List84
17 Decommissioning85
18 Disposal87
19 Technical Data89

Related product manuals

Preview: DURKOPP ADLER D867 M-Type Delta

DURKOPP ADLER D867 M-Type Delta

Preview: DURKOPP ADLER 867-M Premium

DURKOPP ADLER 867-M Premium

DURKOPP ADLER 869-M Premium

Preview: DURKOPP ADLER 878-M PREMIUM

DURKOPP ADLER 878-M PREMIUM

Preview: DURKOPP ADLER 827

DURKOPP ADLER 827

Preview: DURKOPP ADLER 767

DURKOPP ADLER 767

Preview: DURKOPP ADLER 867

DURKOPP ADLER 867

DURKOPP ADLER 806

DURKOPP ADLER 556

Preview: DURKOPP ADLER 745-34-2

DURKOPP ADLER 745-34-2

Preview: DURKOPP ADLER 100-68-1

DURKOPP ADLER 100-68-1

Preview: DURKOPP ADLER 745-34 Speedpocket

DURKOPP ADLER 745-34 Speedpocket