ECKELMANN Compact GLT 3010 - Connections for Safety Extra-Low Voltage (Bottom)

119 pages

Save Page as PDF

To Next Page

To Previous Page



Firmware: V2.18 / V--

26.10.2022

99/119

10.3 Connections for safety extra-low voltage (bottom)

Main Page

Table of Contents3
Conventions6
Warning Signs, Symbols and Text Formatting Used in this Manual6
Explanation of Text Formatting7
Safety Instructions8
Disclaimer in the Event of Non-Compliance9
Requirements for the Personnel9
Intended Use10
Five Safety Rules According to DGUV Regulation 310
Electrostatic-Sensitive Components and Control Components (ESD)11
EGB - Richtlinien zur Handhabung11
Abbreviations Used11
System Design GLT X01012
Connections13
GLT X010 Models16
Number of Data Points17
Synchronisation17
Compatibility17
Tasks of the GLT X01019
Functions of the GLT X010 and Set-Up20
Implementation20
Starting Characteristics21
First Start21
Restart21
Controller Configuration21
Measuring Ranges of the Pt1000 Sensor Inputs23
Measuring Ranges of the Analogue Inputs24
Measuring Ranges of the Analogue Outputs26
Number of SIOX Extension Modules27
System Error Messages28
Process Image (PI)28
Feedback of the Manual Control Level29
Pt1000 Sensor Inputs31
Analogue Inputs32
Analogue Outputs33
System Status34
Status of the CAN Bus35
CAN Bus Address Status36
Status of the SIOX 137
Status of the Battery and DIP Switches38
Status of the Life LED (Life Lamp)39
Signal List40
Formal Structure of the Signal List42
The Column Markers43
Marker $EA1 - Address According to IEC 61131-344
Marker $EA2 - Variable Identifier46
Marker $REF - Channel Reference47
Marker $LDSW, $ARC, $ARCNR - Ldswin Visualisation48
Marker $FTYP, $FTZ, $FN - Probes and Sensors48
Marker $YMIN, $YMAX, $SM, $B, $E, $DEF49
Marker $PRIO - Alarm Priority50
Signal List Tool52
Starting the Tool and Settings54
Menu Functions54
Error Message Examples57
Changes of GLT 5010 Compared to GLT 301058
Codesys59
Creation of the Application Using CODESYS59
Target System Settings61
Importing the Application Using CODESYS63
Connection to Development PC64
Compile Project and Load into DDC66
Create Boot Project and Start Application67
Installation and Start-Up GLT X010 / SIOX68
DIN Rail Mounting69
Mounting on the DIN Rail70
Removal from the DIN Rail71
Handhabung Breiter COMBICON-Stecker72
SIOX Extension Module73
Connection of the SIOX Modules to the Base Module74
Default Hardware Settings75
Settings Using DIP Switch S176
Setting the CAN Bus Address Using Decade Switch S278
Setting of the Interfaces RS485/TTY Using Jumper J179
Configuration of the Analogue Inputs and Outputs80
Power Supply81
Status Leds82
Replacing the Battery83
Firmware Update85
Requirements for Firmware Update85
Update der Aktuellen Firmware86
Connection and Terminal Assignment GLT X010 / SIOX89
Assignment of All Inputs and Outputs89
Connections for 230 V AC (Top)90
Assignment of the 230 V AC Power Supply91
Assignment of the Digital Inputs - 230 V AC / 24 V AC/DC92
Configuration of the Digital Inputs 230 V AC and 24 V AC/DC95
Assignment of the Relay Outputs - 230 V AC / 24 V AC/DC96
Connections for Safety Extra-Low Voltage (Bottom)99
Assignment of the Analogue Inputs100
Assignment of the Analogue Outputs103
Connections for Interfaces (on the Side)104
CAN Bus Assignment105
Assignment RS232 and TTY106
Assignment RS485107
Assignment Modbus Modules108
Assignment SIOX110
Manual / Automatic Operating Modes Changeover111
Decommissioning and Disposal112
Decommissioning / Dismantling112
Disposal112
Alarms and Messages GLT X010113
Message System113
Structure of the Messages113
Message Types114
Setting the Priorities115
Technical Data GLT X010 / SIOX116
Electrical Data GLT X010 / SIOX116
Mechanische Daten GLT X010118
Mechanical Data SIOX Extension Module118
Part Numbers and Accessories GLT X010119

ECKELMANN Compact GLT 3010 - Connections for Safety Extra-Low Voltage (Bottom)

Table of Contents