03-2009 SOI/DT-mdm FCPD-dp Quality-fz 3/91 599 70 56-70
Contents
1.1
Purpose of this manual ....................................................................................................................... 5
1.2 Procedure ........................................................................................................................................... 5
2 WM APPLIANCES CONTROL PANELS ................................................................................................... 6
3 WD APPLIANCES CONTROL PANELS ................................................................................................... 7
4 DIAGNOSTIC SYSTEM............................................................................................................................. 8
4.1 ACCESS TO THE DIAGNOSTIC CYCLE .......................................................................................... 8
4.2 Exiting diagnostics mode .................................................................................................................... 8
4.3 PHASES OF THE DIAGNOSTIC CYCLE .......................................................................................... 9
5 ALARMS .................................................................................................................................................. 11
5.1 Displaying the alarms to the user ..................................................................................................... 11
5.2 Reading the alarm codes.................................................................................................................. 12
5.2.1 Alarm displaying....................................................................................................................... 12
AEG Version: ........................................................................................................................................... 12
5.2.2 Examples of alarm display .......................................................................................................13
5.2.3 Operation of alarms during diagnostics ................................................................................... 13
5.3 Rapid reading of alarm codes........................................................................................................... 14
5.4 Cancelling the last alarm .................................................................................................................. 14
5.5 TABLE OF ALARMS......................................................................................................................... 15
5.6 Notes concerning certain alarm codes ............................................................................................. 18
6 THE DIAGNOSTIC PROGRAMME CANNOT BE ACCESSED .............................................................. 19
6.1.1 All LEDs on the circuit are board switched off ......................................................................... 19
6.1.2 Some of the LEDs of the circuit board light.............................................................................. 19
7 TROUBLESHOOTING ACCORDING TO ALARM CODES .................................................................... 20
E11: Difficulty in filling water during washing phase ............................................................................ 20
E12: Difficulty in filling water during drying phase................................................................................ 22
E13: Water leakage.............................................................................................................................. 23
E21: Difficulty in draining...................................................................................................................... 25
E22: Difficulty in draining water during drying phase ...........................................................................27
E23: Malfunction of the component (triac) that controls the drain pump ............................................. 29
E24: «Sensing» circuit of the component (triac) that controls the drain pump faulty........................... 30
E35: Water level too high ..................................................................................................................... 32
E38: Pressure chamber blocked .......................................................................................................... 33
E3A: Problems with “Sensing” circuit of the heating element relay ..................................................... 34
E41: Door open (3-contact device)....................................................................................................... 35
E41: Door open (4-contact device)....................................................................................................... 37
E42: Problems with door aperture (3-contact device).......................................................................... 39
E42: Problems with door aperture (4- contact device)......................................................................... 41
E44: Door closure «sensing» circuit faulty ........................................................................................... 45
E45: Problems with the «sensing» circuit of the triac that actions the door interlock .......................... 45
E51: Motor power triac short-circuited ................................................................................................. 46
E52: No signal from the motor tachometric generator (first part)......................................................... 47
E52: No signal from the motor tachometric generator (second part)................................................... 49
Procedure for checking the commutator motors .................................................................................. 50
E53: Problems with the "Sensing" circuit of the triac which powers the motor .................................... 51
E54: Motor relay contacts sticking........................................................................................................ 52
E61: Insufficient heating during washing.............................................................................................. 53
E62: Overheating during washing (version WM).................................................................................. 54
E62: Overheating during washing (version WD) .................................................................................. 55
E66: The contacts of the heating element power relay are always closed (version WM).................... 56
E66: The contacts of the heating element power relay are always closed (version WD) .................... 57
E68: Washing heating element leaks current (version WM) ................................................................ 58
E68: Washing heating element interrupted (version WD).................................................................... 59
E69: Washing heating element interrupted (version WM) ................................................................... 60
E69: Washing heating element interrupted (version WD).................................................................... 61
E71: NTC washing sensor faulty .......................................................................................................... 62
E72: Drying NTC sensor on condenser faulty......................................................................................63
E73: NTC sensor on drying duct faulty ................................................................................................ 64
E74: NTC sensor wrongly positioned................................................................................................... 65
E82: Error in reading the RESET/OFF position of the programme selector ........................................ 66
E83: Error in reading the programme selector code ............................................................................ 67
E91: Communication error between user interface and main board.................................................... 68
E92: Protocol incongruence ................................................................................................................. 68
To Next Page
Loading...
