Endress+Hauser SpectraSensors SS500e - Page 9

Hardware Installation and Maintenance Manual v
LIST OF FIGURES
Figure 1–1. Schematic of a typical laser diode absorption spectrometer . . . . . . 1-5
Figure 1–2. Typical raw signal from a laser diode absorption spectrometer
with and without mirror contamination . . . . . . . . . . . . . . . . . . . . 1-6
Figure 1–3. Typical normalized absorption signal from a laser diode
absorption spectrometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Figure 1–4. Typical normalized 2
f signal; species concentration is
proportional to the peak height . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Figure 1–5. SS500e/SS2000e architecture overview . . . . . . . . . . . . . . . . . . . 1-9
Figure 1–6. Electronics control board (AC) for single-channel systems
(SS500e/SS2000e) with RS-232C to RS-485 converter . . . . . . . . 1-10
Figure 1–7. Electronics control board (DC) for single-channel systems
(SS500e/SS2000e) with RS-232C to RS-485 converter . . . . . . . . 1-11
Figure 1–8. Electronics control board (AC) for dual-channel systems
(SS3000e) with RS-232C to RS-485 converter . . . . . . . . . . . . . . 1-12
Figure 1–9. Electronics control board (DC) for dual-channel systems
(SS3000e) with RS-232C to RS-485 converter . . . . . . . . . . . . . . 1-13
Figure 1–10. Electronics control board (AC) for dual-channel systems
(SS3000e) with RS-232C to Ethernet converter . . . . . . . . . . . . . 1-14
Figure 1–11. Electronics control board (DC) for dual-channel systems
(SS3000e) with RS-232C to Ethernet converter . . . . . . . . . . . . . 1-15
Figure 3–1. Analyzer carrying points/methods. . . . . . . . . . . . . . . . . . . . . . . . 3-2
Figure 3–2. AC and DC connection terminal blocks in electronics enclosure. . . . 3-8
Figure 3–3. AC connection terminal block for enclosure heater . . . . . . . . . . . . 3-9
Figure 3–4. Applying conduit lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Figure 3–5. Mating terminal block (TB2) in electronics enclosure for
connecting signal cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Figure 3–6. RJ-45 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3–7. 4-20 mA output board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
Figure 4–1. Probe to analyzer interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure A–1. SS500e/SS2000e analyzer system outline and mounting
dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Figure A–2. SS500e/SS2000e analyzer system sample system schematic. . . . . A-7
Figure A–3. SS500e/SS2000e analyzer system power and signal wiring
diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
Figure A–4. SS3000e single stream analyzer system outline and mounting
dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9
Figure A–5. SS3000e single stream analyzer system sample system
schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Figure A–6. SS3000e single stream analyzer system power and signal
wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
Figure A–7. SS3000e dual stream analyzer system outline and mounting
dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12
Figure A–8. SS3000e dual stream analyzer system sample system
schematic (sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13
Figure A–9. SS3000e dual stream analyzer system sample system
schematic - parts list (sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . A-14
Figure A–10. SS3000e dual stream analyzer system power and signal wiring . . A-15