Need help?Do you have a question about the Excelitas Technologies OmniCure S2000 Elite and is the answer not in the manual?
General| Peak Intensity Wavelength | 365 nm |
|---|---|
| Power Output | 200 W |
| Lamp Life | 2000 hours |
| Input Voltage | 100-240 VAC |
| Input Frequency | 50/60 Hz |
| Light Delivery | Fiber optic light guide |
| Light Source Type | Mercury Short Arc Lamp |
| Wavelength Range | 320-500 nm |
| Output Power/Typical Irradiance | Up to 20 W/cm² |
| Cooling Method | Forced Air |
| Fiber Optic Light Guide Compatibility | 5 mm and 8 mm liquid light guides |
| Applications | Adhesive curing |
| Operating Modes | Continuous |
Overview of the OmniCure S2000 Elite UV curing system and its key features.
Explains the meaning of various warning and informational symbols used in the manual.
Details critical safety measures, warnings, and precautions for operating the S2000 Elite.
Lists all the items included in the S2000 Elite UV Lamp Spot Curing Unit shipping box.
Identifies and explains the components on the front and rear panels of the S2000 Elite unit.
Step-by-step guide on how to install and replace the lamp module in the S2000 Elite.
Instructions on how to properly insert and remove the light guide from the S2000 Elite.
Details the process for installing user-changeable optical filter cartridges into the unit.
Explains the correct procedure for powering the S2000 Elite unit on and off.
Describes the different operating states and modes of the S2000 Elite system.
Guide on adjusting light output intensity using percentage in Relative Mode.
Guide on adjusting light output intensity using irradiance (W/cm²) in Absolute Mode.
Explains the Absolute and Relative intensity modes and the calibration process.
Details how to set and control the exposure time using COUNT UP or COUNT DOWN modes.
Explains the Closed-Loop Feedback (CLF) technology for maintaining irradiance levels.
Describes the main screen and its icons for controlling the S2000 Elite via touch.
Explains how to access and use the web-based interface for controlling the unit remotely.
Details the PLC control signal specifications for digital and analog inputs/outputs.
Provides a pinout table and descriptions for the DB50 PLC connector.
Describes the pin-out and signal for the 3mm audio style foot pedal connector.
Details the signal descriptions for the RS-232 phono connector used with the R2000 Radiometer.
Explains how to interface with the S2000 Elite using original S2000 I/Os via an adapter.
Specifies the COM port settings required for remote communication.
Outlines the RS232 message format and communication protocol for remote control.
Explains StepCure profiles as sequences of instructions for automating tasks.
Describes StepCure elements as the basic building blocks for creating profiles.
Provides examples of pre-defined StepCure profiles for common operations.
Instructions for safely replacing the external fuses of the S2000 Elite unit.
Guide on how to replace the external air filter located under the front faceplate.
Detailed instructions for cleaning the light-emitting end of the light guide.
Instructions for updating system and web software using an SD card and the touchscreen.
Guide for remotely updating system and web software using the Web User Interface.
Instructions for updating the system software using a Windows PC and a USB cable.
Provides physical dimensions and unit weight of the S2000 Elite.
Specifies the correct operating orientation for the S2000 Elite unit.
Details key specifications related to exposure timing and output accuracy.
Provides specifications for the 200W Mercury DC lamp module, including life and warm-up.
Outlines the electrical and protection specifications for the S2000 Elite system.
Lists and describes the various input/output ports available on the S2000 Elite.
Specifies operating and storage conditions for temperature, humidity, and pressure.
Details the radio frequency specifications for the NFC frontend IC.
Discusses electrical noise and methods for shielding the unit in noisy environments.
Lists miscellaneous specifications for the display and keypad.
Information regarding FCC compliance for unintentional radiators.
FCC ID and IC ID information, and compliance for intentional radiators.
Lists relevant EU directives for CE marking compliance.
Information on the WEEE Directive for product disposal and recycling.
Substance information for China RoHS regulations.
Details optical safety classification and labeling based on IEC 62471.
Details the warranty terms and conditions for the S2000 Elite replacement lamp.
Instructions for returning the S2000 Elite unit for service or repair.
To Next Page