Installation manual
CNC 8055
CNC 8055i
F.
SOFT: V02.2X
·665·
Summary of internal CNC variables.
Operating-mode related variables.
Other variables.
Variable CNC PLC DNC
( section 13.17 )
OPMODE R R R Operation mode.
OPMODA R R R Operating mode when working in the main channel.
OPMODB R R R Type of simulation.
OPMODC R R R Axes selected by handwheel.
Variable CNC PLC DNC
( section 13.18 )
NBTOOL R - R Number of the tool being managed..
PRGN R R R Number of the program in execution.
BLKN R R R Label number of the last executed block.
GSn R - - Status of the indicated G function (n).
GGSA - R R Status of functions G00 thru G24.
GGSB - R R Status of functions G25 thru G49.
GGSC - R R Status of functions G50 thru G74.
GGSD - R R Status of functions G75 thru G99.
GGSE - R R Status of functions G100 thru G124.
GGSF - R R Status of functions G125 thru G149.
GGSG - R R Status of functions G150 thru G174.
GGSH - R R Status of functions G175 thru G199.
GGSI - R R Status of functions G200 thru G224.
GGSJ - R R Status of functions G225 thru G249.
GGSK - R R Status of functions G250 thru G274.
GGSL - R R Status of functions G275 thru G299.
GGSM - R R Status of functions G300 through G324.
GGSN - R R Status of functions G325 thru G349.
GGSO - R R Status of functions G350 thru G374.
GGSP - R R Status of functions G375 thru G399.
GGSQ - R R Status of functions G400 thru G424.
MSn R - - Status of the indicated M function (n)
GMS - - R Status of M functions: M (0..6, 8, 9, 19, 30, 41..44).
PLANE R R R Abscissa and ordinate axes of the active plane.
LONGAX R R R Axis affected by the tool length compensation (G15).
MIRROR R R R Active mirror images.
SCALE R R R General scaling factor applied. Reading from the PLC in ten-thousandths.
SCALE(X-C) R R R Scaling Factor applied only to the indicated axis. Reading from the PLC in
ten-thousandths.
ORGROT R R R Rotation angle (G73) of the coordinate system.
ROTPF R - - Abscissa of rotation center.
ROTPS R - - Ordinate of rotation center.
PRBST R R R Returns probe status.
CLOCK R R R System clock in seconds.
TIME R R R/W Time in hours-minutes-seconds format.
DATE R R R/W Date in year-month-day format.
TIMER R/W R/W R/W Clock activated by PLC, in seconds.
CYTIME R R R Time to execute a part in hundredths of a second.
PARTC R/W R/W R/W Parts counter of the CNC.
FIRST R R R First time a program is executed.
KEY R/W R/W R/W keystroke code.
KEYSRC R/W R/W R/W Source of the keys.
ANAIn R R R Voltage (in volts) of the indicated analog input (n).
ANAOn R/W R/W R/W Voltage (in volts) to apply to the indicated output (n).
CNCERR - R R Active CNC error number.
PLCERR - - R Active PLC error number.
DNCERR - R - Number of the error generated during DNC communications.
AXICOM R R R Pairs of axes switched with function G28.
To Next Page
Loading...
