Name: Flowserve MX
Brand: Flowserve
Rating: 4 (1 reviews)

Default Chapter2

Table of Contents2

1 Important Notes8

2 Quick Start10

3 Installation and Operation15

Preparing the Stem Nut15
Type "B" Bases: Torque-Only Applications15
Figure 3.1 - B4 Base15
Figure 3.2 - B4E Base16
Figure 3.3 - Exploded View of B4/B4E Base (MX-05 Shown)16
Type "A" Bases: Thrust-Only Applications17
Figure 3.4 - B1 Base17
Figure 3.5 - Exploded View of B1 Base17
Figure 3.6 - A1 Base17
Figure 3.7 - Exploded View of A1/A1E Base (MX-05/10/20/40 Only)18
Table 3.1 - Hardware and Torque for Thrust Base Mounting19
Figure 3.8 - Exploded View of Thrust Base (MX-85 Only)20
Type "BL" Drive: Splined Drive Application21
Mechanical Installation Onto Valve or Gearbox21
Figure 3.9 - Exploded View of Thrust Base (MX-140/MX-150 Only)21
Mounting (Type "B" Bases): Torque-Only22
Removal (Type "B" Bases): Torque-Only22
Mounting (Type "A" Bases): Thrust-Only22
Removal (Type "A" Bases): Thrust-Only22
Electrical Connections23
- Removing Terminal Cover23
- Terminal Compartment Documents23
- Sealing Cable/Conduit Entries23
- Recommended Terminal Connections23
- Figure 3.10 - Power Terminal Connector Size Limitations24
- Figure 3.11 - Terminal Block Rating; Power Terminals24
- Figure 3.12 - Control Terminal Connector Size Limitations24
- Termination of Cables25
- Cable Connections25
- Network Installations25
- Table 3.2 - Terminal Block Rating; Control Terminals25
- Table 3.3 - Required Ratings for External Wires25
- Figure 3.13 - View of Terminal Block26
- Figure 3.14 - Standard Wiring Diagram26
- Figure 3.15 - Removing Outer Plastic Jacket27
- Figure 3.16 - Separating Cable Parts27
- Figure 3.17 - Stripping Conductors and Applying Heat Shrink Tubing28
- Figure 3.18 - Ring Tongue Connectors28
- Table 3.4 - Loop Topology Connections28
- Foundation Fieldbus Installation29
- Table 3.5 - Foundation Fieldbus Connections29
- Network Wiring - Profibus DP/PA Installation30
- Network Wiring - Devicenet30
- Table 3.6 - Profibus Cable Specifications30
- Table 3.7 - Devicenet Cable Specifications30
- HART Installation31
- Replacing Terminal Cover31
- External Earth/Ground Connections31
Terminal Block Shield Installation31
Commissioning the Actuator31
- Figure 3.19 - Terminal Block Shield31
- Default Configuration Set32
- Figure 3.20 - User Network Connection for Loop Topology/Typical for All Two-Wire Network Protocols32
- Figure 3.21- External Earth/Ground Connection - Housing32
- Entering the Setup Mode33
- Table 3.8 - Default Configurations33
- View the Existing Settings33
- Figure 3.22 - View Settings34
- Setting Position Limits34
- Figure 3.23 - Position Setup - Electrical Operation36
Operating the MX Actuator37
- Manual Operation37
- Electrical Operation37
- Local Control37
- Figure 3.24 - Declutch Lever Shows Direction of Engagement (MX-05 Shown)37
- Remote Control38
- Local Indication38
- Figure 3.25 - Control Panel38
- Table 3.9 - LED Indicators - Default Settings38

4 Customizing the Actuator39

5 Troubleshooting87

6 Maintenance100

Lubrication100
- Oil Capacities100
- Checking Oil Level100

7 Regulatory Information101

Brand	Flowserve
Model	MX
Category	Controller
Language	English

Flowserve MX User Manual

Table of Contents

Questions and Answers:

Flowserve MX Specifications

Related product manuals