Home
Fluke
Test Equipment
ScopeMeter 190 II Series
Fluke ScopeMeter 190 II Series Service Manual
5
of 1
of 1 rating
142 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Fluke 190-
062, -102
, -104, -202,
-204, -502, -504
Service Manual
4-40
Probe Cal
Probe Cal Ref.
st8416_t.eps
Figure 4-15. Probe Cal
ibration
This is the end of the Perfor
mance Verification Procedure.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
84
86
Table of Contents
Default Chapter
4
Table of Contents
4
Safety Instructions
12
Chapter 1
14
Introduction
14
Safety Precautions
14
Caution and Warning Statements
14
Symbols
15
Li-Ion Battery Pack
18
Safe Storage of Battery Pack
18
Safe Use of Battery Pack
19
Safe Transport of Battery Pack
20
Safe Disposal of Battery Pack
20
Specifications
22
Chapter 2
24
Introduction
24
Oscilloscope
24
Edge Trigger
26
Video Trigger
26
Pulse Width Trigger
26
Automatic Scope Measurements
27
Meter Measurements for Fluke 190-Xx4
30
Meter Measurements for Fluke 190-Xx2
30
Recorder
32
Zoom, Replay and Cursors
33
Miscellaneous
33
Cursor Measurements
33
Environmental
35
Certifications
35
Safety
35
10:1 Probe VPS410
37
Electromagnetic Immunity
37
Parts List
38
Chapter 3
40
Introduction
40
How to Obtain Parts
40
Final Assembly Parts
41
Accessory List
45
Performance Verification
46
Chapter 4
48
Introduction
48
Equipment Requirements for Verification
49
General Instructions
49
Operation Instructions
49
Reset the Test Tool
49
Menu Navigation
50
Standard Test Tool Setup
50
Display and Backlight Test
52
Scope Input A, B, C, D Tests
53
Input A, B, C, D Vertical Accuracy Test
53
Input A, B, C, D DC Voltage Accuracy Test
56
Input A, B, C, D AC Voltage Accuracy Test (LF)
59
Input A, B, C, D AC-Coupled Lower Frequency Test
61
Input A, B, C, D Peak Measurements Test
62
Input A, B, C, D Frequency Measurement Accuracy Test
63
Input A&B / C&D Phase Measurements Test
64
Time Base Test
65
Input a Trigger Sensitivity Test
66
Input a AC Voltage Accuracy (HF) and Bandwidth Test
68
Input B Trigger Sensitivity Test
69
Input B AC Voltage Accuracy (HF) and Bandwidth Test
70
Input C Trigger Sensitivity Test
71
Input C AC Voltage Accuracy (HF) and Bandwidth Test
72
Input D Trigger Sensitivity Test
73
Input D AC Voltage Accuracy (HF) and Bandwidth Test
75
Video Test with SC600 Scope Calibration Option
76
External Trigger Level Test
79
Meter Tests
80
Meter DC Voltage Accuracy Test
80
Meter (DMM) Tests
80
Meter AC Voltage Accuracy and Frequency Response Test
81
Continuity Function Test
82
Diode Test Function Test
82
Ohms Measurements Test
83
Probe Calibration Generator Test
84
Calibration Adjustment
86
Chapter 5
88
Introduction
88
General
89
Calibration Number and Date
89
General Instructions
89
Equipment Required for Calibration
90
Calibration Procedure Steps
90
How to Start the Calibration
91
Contrast Calibration Adjustment
92
Warming-Up and Pre-Calibration
94
Final Calibration for V11.10 and Later
95
Warming-Up 2, Warm-Up Final, and ADC Timing
96
Input a LF-HF Gain
97
Input B LF-HF Gain
99
Input C LF-HF Gain
101
Input D LF-HF Gain
103
Input AB Position
105
Input AB LF-HF Gain and Position
105
Input Pos ABCD (AB) Calibration
107
Input ABCD (AB) Noise F FBW Calibration
107
Input AB Volt Gain
107
Multimeter Meter Zero
109
Multimeter Volt Gain
109
Multimeter Ohm Gain
111
Final Calibration (Firmware: V10.9 and Lower)
113
Error Messages
113
Warm-Up Final and ADC Timing
113
Input a LF-HF Gain
114
Input B LF-HF Gain
116
Input C LF-HF Gain
118
Input D LF-HF Gain
120
Input ABCD (AB) LF-HF Gain
121
Input ABCD (AB) Position
123
Input ABCD (AB) Volt Gain
123
Input ABCD (AB) Zero
124
Multimeter Volt Gain
125
Multimeter Numeric Zero
126
Multimeter Ohm Gain
126
Save Calibration Data and Exit
128
Probe Calibration
129
Disassembly
132
Chapter 6
134
Introduction
134
Disassembly and Reassembly Procedures
134
Required Tools
134
Remove the Tilt Stand, Hang Strap, and Side Strap
134
Open the Test Tool, Remove the Battery Pack
135
How to Access the Top Side of PCA
136
How to Access the Bottom Side of PCA
136
Access to LCD, Keypad Foil, and Keypad
137
Disassembly Steps
137
Other manuals for Fluke ScopeMeter 190 II Series
User Manual
278 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Fluke ScopeMeter 190 II Series and is the answer not in the manual?
Ask a question
Fluke ScopeMeter 190 II Series Specifications
General
Brand
Fluke
Model
ScopeMeter 190 II Series
Category
Test Equipment
Language
English
Related product manuals
Fluke ScopeMeter 190 Series III
97 pages
Fluke ScopeMeter 190-202
278 pages
Fluke ScopeMeter 190-204
278 pages
Fluke ScopeMeter 190-062
278 pages
Fluke ScopeMeter 192B
122 pages
Fluke ScopeMeter 123
170 pages
Fluke 190-102
278 pages
Fluke ST120
6 pages
Fluke SimpliFiber Pro
76 pages
Fluke 725
72 pages
Fluke 707
16 pages
Fluke 6200
39 pages