FUTABA T18MZ WC - Condition Select

116
＜
Model Menu (Common Functions)
＞
ŏ5HWXUQWR0RGHO0HQX
ŏ7RXFKWKH>&RQGLWLRQ6HOHFW@EXWWRQLQWKH0RGHO
Menu to call the setup screen shown below.
&RQGLWLRQ6HOHFW
Flight conditions addition, deletion, copy, condition renaming, and
FRQGLWLRQGHOD\FDQEHVHW>$OOPRGHOW\SHV@
The functions in the Model Menu can be used by
switching the settings of up to 8 flight conditions
by using the Condition Select function to add Àight
conditions. Add conditions, as required.
When you do not want to use the Condition Select
function, this setting is unnecessary. In this case, use
the Àight conditions (Condition 1) assigned at initial
setting.
ŏ6LQFHVZLWFKLQJE\VWLFNDQGOHYHUSRVLWLRQLQ
addition to ordinary toggle switch, is possible
as the flight condition selector switch, this
IXQFWLRQFDQEHOLQNHGZLWKRWKHURSHUDWLRQV
ŏ$&RQGLWLRQ'HOD\IXQFWLRQFDQEHVHW
Unnecessary fuselage motion generated
when there are sudden changes in the servo
positions and when there are variations in
the operating time between channels during
condition switching can be suppressed. The
delay can be set for each channel.
When setting the delay function at the
switching destination condition, the related
function changes after a delay corresponding
to the set amount.
ŏ:KHQPXOWLSOHFRQGLWLRQVDUHVHWWKHLU
operation priority can be freely changed.
ŏ7KHFRQGLWLRQQDPHFDQEHFKDQJHG7KH
selected condition name is displayed on the
screen. When a condition has been added,
JLYHLWDQDPHZKLFKFDQEHHDVLO\FRQÀUPHG
(Conditions List)
3ULRULW\FKDQJH
1. Touch the condition whose priority
you want to change in Conditions
List.
2. Change the priority with the
SULRULW\>
@RU> @EXWWRQ7KHODVW
condition has the highest priority.)
*The initial setting condition cannot
be moved. It has the lowest
priority.
&RQGLWLRQ$GGLWLRQ
:KHQWKH>$GG@EXWWRQLVWRXFKHGWKH
&RQGLWLRQ6HOHFWVFUHHQDSSHDUV
*Only the number of buttons
corresponding to the conditions which
can be added are displayed.
6HOHFWWKHGHVLUHGFRQGLWLRQVE\
touching the buttons.
*The selected conditions are added to
Conditions List.
7RXFKWKH>18//@EXWWRQWRFDOOWKH
6ZLWFK!VFUHHQ
6HOHFWWKHVZLWFKWREHXVHGLQFRQGLWLRQ
switching.
(For a description of the switch selection
method, see next page.)
5. The "Condition 1" data for the added
conditions is copied.
&RQGLWLRQ5HVHW
6HOHFWWKHFRQGLWLRQ
by touching the
condition you want
to reset in Conditions
List.
7RXFKWKH>5HVHW@
button.
:KHQWKH><HV@
button is touched,
the condition is reset.
(To abort resetting,
WRXFKWKH>1R@
button.)
&RQGLWLRQ5HQDPLQJ
6HOHFWWKHFRQGLWLRQE\
touching the condition
you want to rename in
Conditions List.
7RXFKWKH>5HQDPH@
button.
3. Enter the new name from
WKHNH\ERDUGZKLFK
appears on the screen.
:KHQWKHNH\ERDUG
>5HWXUQ@NH\LVWRXFKHG
the new name is
registered. (To abort
registration, touch the
>(6&@NH\
&RQGLWLRQ&RS\
7RXFKWKH>&RS\@EXWWRQ7KH&RS\VFUHHQDSSHDUV
6HOHFWWKHFRQGLWLRQE\WRXFKLQJWKHEXWWRQRIWKHFRS\
source conditions.
1H[WVHOHFWWKHFRQGLWLRQE\WRXFKLQJWKHFRS\
destination condition.
7RXFKWKH>&23<@EXWWRQ
:KHQWKH><HV@EXWWRQLVWRXFKHGWKHGDWDLVFRSLHG7R
DERUWFRS\LQJWRXFKWKH>1R@EXWWRQ
(Currently selected condition name)
ŏ&RQGLWLRQGHOD\
setting
(For a description of
the setting method,
see the next page.)
+(/,&237(5
$,53/$1(
*/,'(5