FUTABA T18MZ WC - Setting Methods: Curve Mixing

121
＜
Model Menu (Common Functions)
＞
6HWWLQJPHWKRGV&XUYHPL[LQJ
ŏ*URXSVLQJOHPRGHVHOHFWLRQ
Activating functions for only the selected
FRQGLWLRQV
7RXFKWKH*URXSEXWWRQDQGVZLWFKWRWKH
6QJOPRGH
*Each time the button is touched, it toggles between
WKH*UDQG6QJOPRGHV
ŏ0L[LQJVHWXSVFUHHQVHOHFWLRQ
1. Touch the button of the mixing you want
to set. The mixing setup screen is displayed.
Activate the function.
$FWLYDWHWKHIXQFWLRQE\WRXFKLQJWKH>,1+@
button.
*Each time this button is touched, it toggles between
>,1+@DQG>212))@
ŏ0L[LQJ212))VZLWFKVHWWLQJDQG212))
direction switching
$Q212))VZLWFKLVQRWVHWHYHQZKHQWKHIXQFWLRQ
is activated.
:KHQ\RXZDQWWRWXUQPL[LQJ212))E\
VZLWFKWRXFKWKH>18//@EXWWRQWRFDOOWKH
6ZLWFK!VFUHHQDQGWKHQVHOHFWWKHVZLWFK
DQGLWV21GLUHFWLRQ
*For a description of the selection method, see
>6ZLWFK6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
ŏ0DVWHUFKDQQHOVHWWLQJ
1. Touch the Master button to call the Function
menu and select the master channel.
7ROLQNWKLVPL[LQJZLWKRWKHUPL[LQJWRXFKWKH
button at the left of the master channel and
VHOHFWOLQN
*Each time the button is touched, it toggles between
PL[LQJGLUHFWLRQDQGDQG1RGLVSOD\QROLQN
0DVWHUFKDQQHOFRQWUROFDQEHVHWWRVWLFN95DQG
RWKHUVLPSOHWUDYHOVZKLFKGRQRWLQFOXGH$79$)5
'5PL[LQJVHWWLQJHWF,QWKLVFDVHGLVSOD\WKH
6ZLWFK!VFUHHQE\WRXFKLQJWKH>+:@EXWWRQDQG
then select master channel side control.
ŏ6ODYHFKDQQHOVHWWLQJ
7RXFKWKH6ODYHEXWWRQWRFDOOWKH)XQFWLRQ
menu and select the slave channel.
7ROLQNWKLVPL[LQJZLWKRWKHUPL[LQJWRXFK
the button at the right-hand side of the slave
FKDQQHODQGVHOHFWOLQN
*Each time the button is pressed, it toggles between
PL[LQJGLUHFWLRQDQGDQG1RGLVSOD\QROLQN
ŏ7ULPPRGH212))VHWWLQJ
7RWXUQWKHWULPPRGH212))WRXFKWKH7ULP
button on the screen.
*When mixing includes master side trim, set the Trim
EXWWRQWR>21@:KHQPL[LQJGRHVQRWLQFOXGH
PDVWHUVLGHWULPVHWWKH7ULPEXWWRQWR>2))@
*Each time this button is pressed, it toggles between
>21@DQG>2))@
*This is effective when the master channel is set by
Function.
ŏ6ODYHFKDQQHO$)5PRGH67.ń67.
:KHQ/LQNLVVHWDWWKHVODYHVLGHDQG\RX
ZDQWWRDGG$)5'5WRWKHPL[LQJUDWH
VHOHFW>21@:KHQ\RXGRQRWZDQWWRDGG
$)5'5WRWKHPL[LQJUDWHVHOHFW>2))@
*Each time this button is pressed, it toggles between
>21@DQG>2))@
7KLVLVHIIHFWLYHZKHQPDNLQJFRUUHFWLRQVZKHQWKH
fuselage is the same but the rudder angles are
substantially different.
ŏ0L[LQJFXUYHW\SHVHOHFWLRQ
1. Touch the curve type selection button of the
curve type you want to use to display the
selection screen and then select the curve
you want to use.
*For a description of the curve setting method, see
WKHGHVFULSWLRQDWWKHEDFNRIWKLVPDQXDO
ŏ)LQHWXQLQJWULPVHWWLQJ
1. When using the curve fine tuning function,
WRXFKWKH>18//@EXWWRQRIWKH)LQH7XQLQJ
LWHPWRFDOOWKH6ZLWFK!VFUHHQDQGWKHQ
VHOHFWWKHOHYHU95HWF\RXZDQWWRXVH
*For a description of the fine tuning trim setting
PHWKRGVHHWKHGHVFULSWLRQDWWKHEDFNRIWKLV
manual.
ŏ6HUYRVSHHGVHWWLQJ
1. When setting the servo speed, touch the
6SHHGEXWWRQ7KH6HUYR6SHHGVHWXSVFUHHQ
is displayed.
*For a description of the servo speed setting method,
VHHWKHGHVFULSWLRQDWWKHEDFNRIWKLVPDQXDO
2IIVHWPL[LQJFKDQJHVWKHVSHHG8VHWKH6SHHG,Q
DQG6SHHG2XWEXWWRQVWRUHDGMXVWWKHVSHHG
The mixing switch can set a delay with a different
rate at starting and stopping.
*This function is inactive when a mixing switch is not
set.
ŏ7KHSURJUDPPDEOHPL[LQJLQPL[LQJPRGH67.
WR67.PL[LQJIXQFWLRQFDQEHXVHGHYHQZKHQ
WKH0DVWHUIXQFWLRQLVFRQWUROOHGE\DVWLFNRU
other hardware.
+(/,&237(5
$,53/$1(*/,'(5