FUTABA T18MZ WC - Operations Related to Servo Speed

168
＜
Data
＞
Servo speed setting (1)
,1
 
6SHHG
287
The speed during operation (including flight
condition switching) can be adjusted. The
servos operate smoothly at a constant speed
corresponding to the speed set for them. The
operation speed (In Speed) and the return speed
(Out Speed) can be set individually.
Switch the operation mode according to the set
function. When the button is touched, it toggles
between [LIN] and [SYM].

"SYM" mode: Mode used with ailerons and
other self-neutral functions
"LIN" mode: Mode used with functions which
hold the operation position of the throttle
and switch channel, etc.
>6HWWLQJPHWKRG@
6HOHFWWKHIXQFWLRQ>/,1@RU
>6<0@PDWFKHGWRWKHPDVWHU
channel. Each time the
button is touched, it toggles
EHWZHHQ>/,1@DQG>6<0@
7RXFKWKH,QRU2XW6SHHG
button and set the servo
speed.
Initial value: 0
6HWWLQJUDQJHa
Operations related to servo speed
speed corresponding to the set speed.
Master mode: The servo movement is
traced by the setting curve. The trace
VSHHGLVDGMXVWHGE\LQDQGRXWVSHHG
>6HWWLQJPHWKRG@
1. When setting the servo speed, touch the
Speed button. The Servo Speed setup
screen shown above is displayed.
6HOHFWWKHIXQFWLRQ>/,1@RU>6<0@PDWFKHG
to the master channel. Each time the
EXWWRQLVWRXFKHGLWWRJJOHVEHWZHHQ>/,1@
DQG>6<0@
"SYM" mode: Mode used with ailerons and
other self-neutral functions.
"LIN" mode: Mode used with functions
which hold the operating position of the
throttle and switch channel, etc.
3. Touch the In Speed button and set the
servo speed.
Initial value: 0
 6HWWLQJUDQJHa
7RXFKWKH2XW6SHHGEXWWRQDQGVHWWKH
servo speed.
Initial setting: 0
 6HWWLQJUDQJHa
5. Touch the Start Delay button and set the
GHOD\WLPHIURPVZLWFK21WRWKHVWDUWRI
function operation.
Initial setting: 0.0 sec
 6HWWLQJUDQJHaVHFV
6. Touch the Stop Delay button and set the
GHOD\WLPHIURPVZLWFK2))WRWKHVWDUWRI
function operation.
Initial setting: 0
 6HWWLQJUDQJHaVHFV
$WPDVWHUPRGH
1. Set desired in and out speed.
2. Select the master channel to any toggle
switch.
3. The slave channel's servo traces the setting
curve as the master toggle switch is moved.
%HORZWKHFDVH$8;VHUYRWUDFHVDQ(;3
FXUYHDVWKH6:)LVRSHUDWHG
5HVHW
Servo speed setting (2) (Prog. Mix only)
6HUYR6SHHG
,Q6SHHG
2XW6SHHG
6WDUW'HOD\
6WRS'HOD\

&ORVH
 6ODYH
ۢ
ۢ
Speed mode: Slave/Master
The speed mode can be selected.
Slave mode: The speed at programmable
PL[LQJVZLWFKLQJFDQEHDGMXVWHG7KH
servos operate smoothly at a constant