GE Power Management
ALPS Advanced Line Protection System i
INDEX
INDEX
INDEX
Numerics
1PDELAY1 (Protection Settin
1804)................................ 2-42
1PDELAY2 (Protection Settin
1805)................................ 2-42
1PDELAY3 (Protection Settin
1806)................................ 2-42
1PDELAY4 (Protection Settin
1807)................................ 2-43
3PDELAY1 (Protection Settin
1809)................................ 2-43
3PDELAY2 (Protection Settin
1810)................................ 2-43
3PDELAY3 (Protection Settin
1811)................................ 2-43
3PDELAY4 (Protection Settin
1812)................................ 2-43
50 (Protection Settin
601)............................................... 2-25
50 FUNCTION ................................................1-11, 1-22, 2-25
directional control of ...................................................... 2-25
fuse failure blockin
...................................................... 2-29
pickup settin
........................................................2-25, 2-26
50_DIRCNL (Protection Settin
602)................................. 2-25
50G (Protection Settin
605) ............................................ 2-26
50G FUNCTION ....................................... 1-4, 1-11, 1-22, 1-37
directional control of ...................................................... 2-26
fuse failure blockin
...................................................... 2-29
maximum postive value.................................................. 2-26
operatin
quantity.......................................................... 2-26
pickup ........................................................................... 2-26
recloser blockin
........................................................... 2-29
restraint ........................................................................ 2-26
settin
........................................................................... 2-26
50G_BLOCK (Protection Settin
804) ............................... 2-29
50G_DIRCNL (Protection Settin
606) .............................. 2-26
50GPICKUP (Protection Settin
607) ................................ 2-26
calculatin
..................................................................... 2-26
50GPICKUPFF (Protection Settin
608) ............................ 2-26
50GRESTNT (Protection Settin
609) ............................... 2-26
with50G operatin
quantity ............................................ 2-26
50PICKUP (Protection Settin
603) .................................. 2-25
50PICKUPFF (Protection Settin
604) .............................. 2-26
51G (Protection Settin
610) ............................................ 2-26
51G FUNCTION ................................................1-4, 1-11, 1-37
characteristic curve shape ............................................. 2-27
directional control of ...................................................... 2-27
fuse failure blockin
...................................................... 2-29
operatin
quantity.......................................................... 2-27
pickup ........................................................................... 2-27
settin
........................................................................... 2-26
time-dial settin
............................................................. 2-27
51G_RESET (Protection Settin
617) ............................... 2-27
51GCURVE (Protection Settin
614)................................. 2-27
51GDIRCNL (Protection Settin
611) ................................ 2-27
51GPICKUP (Protection Settin
612) ................................ 2-27
51GPICKUPFF (Protection Settin
613) ............................ 2-27
51GTIMDIAL (Protection Settin
615) ............................... 2-27
52/A CONTACT .......................................................1-18, 1-19
52/B CONTACTS ..............................................1-25, 1-27, 2-2
blockin
scheme............................................................ 2-34
hybrid scheme............................................................... 2-34
POTT1 scheme ............................................................. 2-34
POTT2 scheme ............................................................. 2-34
PUTT scheme ............................................................... 2-34
A
A1 (Protection Settin
2007) ............................................ 2-46
A10 (Protection Settin
2016)........................................... 2-46
A11 (Protection Settin
2017)........................................... 2-46
A12 (Protection Settin
2018)........................................... 2-46
A2 (Protection Settin
2008) .............................................2-46
A3 (Protection Settin
2009) .............................................2-46
A4 (Protection Settin
2010) .............................................2-46
A5 (Protection Settin
2011) .............................................2-46
A6 (Protection Settin
2012) .............................................2-46
A7 (Protection Settin
2013) .............................................2-46
A8 (Protection Settin
2014) .............................................2-46
A9 (Protection Settin
2015) .............................................2-46
ACCEPTANCE/PERIODIC TESTS.......................................4-1
AC system input test ......................................................4-10
confi
urable input test......................................................4-9
confi
urable output test....................................................4-9
di
ital output test .............................................................4-8
display test ......................................................................4-7
enterin
test mode ...........................................................4-6
exitin
test mode .............................................................4-6
eneral instructions..........................................................4-2
eneral relay tests ...........................................................4-1
initial test setup ...............................................................4-6
introduction .....................................................................4-1
keypad test......................................................................4-7
relay status......................................................................4-7
required settin
s ..............................................................4-2
settin
chan
es ...............................................................4-3
test equipment.................................................................4-1
test unit description..........................................................4-5
ACCURACIES ....................................................................7-2
ACT KEY
menu .............................................................................. D-2
usin
ACTIONS ....................................................................... 11-12
editin
.............................................................................8-8
list...................................................................................8-8
ACTIVE SETTINGS GROUP
selectin
..........................................................................8-7
ADAPTIVE MEMORY
with Zone 4 phase distance functions .............................2-19
ADAPTIVE REACH .............................................................1-4
ALARMS ..........................................................................1-19
continuous monitor alarm ...............................................1-22
critical .............................................................................4-3
critical alarm ..................................................................1-19
line overload..................................................................1-19
non-critical...........................................1-16, 1-19, 1-22, 2-46
overcurrent ........................................................... 1-19, 1-22
power supply .................................................................1-19
trip circuit alarm.................................................... 1-19, 1-22
unbalanced current detector .................................. 1-22, 2-25
zone fla
s on ........................................................ 1-19, 1-22
ALL_3_Z2PH (Protection Settin
803) ...............................2-29
ALL_BELOW (Protection Settin
801) ...............................2-29
ALPS
communications ........................................................2-4, 4-4
default settin
s ................................................................4-5
servicin
..........................................................................9-1
status check ....................................................................4-7
test mode ........................................................................4-4
ALPS-LINK
breaker health report....................................................11-15
calculation of settin
s ......................................................2-1
chan
e password ......................................................... 11-12
chan
in
output settin
s ................................................2-46
close breaker ............................................................... 11-13
communications ................................. 2-4, 2-5, 4-4, 11-9, A-1
contact status report .................................................... 11-16
date & time .................................................................. 11-11
demand report ............................................................. 11-15
To Next Page
