GE ALPS - Page 354

ii ALPS Advanced Line Protection System
GE Power Management
INDEX
INDEX
device setup ......................................................... 11-7, 11-8
dia
g
nostics report ........................................................ 11-15
di
g
ital output test ......................................................... 11-13
disable outputs ............................................................ 11-12
enable outputs ............................................................. 11-12
event report ................................................................. 11-15
explicit han
g
-up ............................................................. 11-9
fault report................................................................... 11-15
g
et lo
g
ic command ....................................................... 11-11
installation.....................................................................11-3
local pc confi
g
uration ....................................4-5, 11-6, 11-11
lo
gg
in
g
........................................................................ 11-17
lo
gg
in
g
into the relay .......................................................4-5
lo
g
out from device ......................................................... 11-9
LUI password report..................................................... 11-16
menu bar ....................................................................... 11-5
modem setup ................................................................. 11-6
new report ...................................................................11-14
on-line help ...................................................................11-1
open breaker ............................................................... 11-13
open report........................................................11-14, 11-16
oscillo
g
raphy report ..................................................... 11-15
port setup ...................................................................... 11-6
present values report ................................................... 11-15
printin
g
............................................................... 11-7, 11-16
protection cate
g
ory scroll list........................................ 11-11
relay test ..................................................................... 11-13
reset data .................................................................... 11-13
save report .................................................................. 11-16
session lo
g
.................................................................. 11-17
settin
g
chan
g
es ...............................................................4-6
settin
g
s ....................................................................... 11-10
software setup .................................................................4-4
startin
g
................................................................... 4-5, 11-5
status bar ...................................................................... 11-5
status report ................................................................ 11-15
supported architecture .......................................... 11-1, 11-2
test mode ................................................................. 4-6, 6-3
test unit description .........................................................4-5
TOC curves ................................................................. 11-12
toolbar........................................................................... 11-5
trippin
g
breakers with.......................................................2-2
troubleshootin
g
............................................................... A-2
upload settin
g
s ............................................................ 11-10
with GEmodem protocol ...................................................2-5
with Windows NT ............................................................ A-2
ALPS-SET
calculation of settin
g
s ......................................................2-1
chan
g
e model number dialo
g
box ................................... 14-1
edit menu - copy settin
g
s report .....................................14-3
help menu .....................................................................14-4
installation.....................................................................14-1
new settin
g
s .................................................................. 14-1
printin
g
.......................................................................... 14-3
selectin
g
protection scheme ........................................... 14-2
tools menu .................................................................... 14-3
version number.............................................................. 14-4
ALPS-TEST
close test file .................................................................10-9
copyin
g
mho circles ..................................................... 10-11
description..................................................................... 10-1
edit menu .................................................................... 10-11
enterin
g
values ..................................................... 10-2, 10-3
exitin
g
pro
g
ram............................................................ 10-10
file menu .............................................................. 10-1, 10-8
help menu ................................................................... 10-16
input test........................................................................10-3
MOB phase unit .............................................................10-5
new test file ...................................................................10-8
open test file ..................................................................10-8
printin
g
........................................................................10-10
save input quantities ...........................................10-9, 10-10
save output ..................................................................10-10
selectin
g
values .............................................................10-3
status bar ....................................................................10-12
test calculations ....................................................10-1, 10-2
toolbar .........................................................................10-12
tools menu ...................................................................10-13
version.........................................................................10-16
view menu ...................................................................10-12
viewin
g
multiple tests ...................................................10-15
window menu ...............................................................10-15
Zone 1 functions ...................................................10-3, 10-6
Zone 2 functions ...................................................10-4, 10-6
Zone 3 functions ...................................................10-4, 10-7
Zone 4 functions ...................................................10-5, 10-7
ANYZ2PHASE (Protection Settin
g
809) .............................2-30
APPLICATIONS OF THE ALPS .......................................... 1-4
ARROW KEYS................................................................... 8-2
ASCII ...............................................................................8-23
communications .............................................................12-1
ASSEMBLY ....................................................................... 3-1
AUXILIARY PROTECTION FUNCTIONS............................1-11
B
BACKUP PROTECTION TESTS ......................................... 6-8
BLOCK DIAGRAM ............................................................. 3-4
BLOCKING SCHEME .................................................1-8, 1-30
CARRSTART and IPBKFACTOR settin
g
s ........................2-23
IPB/IPT functions ...........................................................2-23
lo
g
ic dia
g
ram .................................................................1-31
overcurrent functions......................................................2-22
remote open detector .....................................................2-31
selectin
g
........................................................................2-32
start carrier ....................................................................2-33
timer TL1 .......................................................................2-33
timer TL24 .....................................................................2-35
timer TL25 .....................................................................2-35
timer TL4 .......................................................................2-34
timer TL5 .......................................................................2-34
Zone 1 functions ............................................................2-11
Zone 2 functions ............................................................2-14
Zone 4 functions ..........................................2-19, 2-20, 2-21
BLOCKWHAT (Protection Settin
g
1603).............................2-38
BLOCKZ1 (Protection Settin
g
1604) .........................1-14, 2-38
BLOCKZ2 (Protection Settin
g
1605) .........................1-14, 2-38
BLOCKZ3 (Protection Settin
g
1606) .........................1-14, 2-39
BLOCKZ4 (Protection Settin
g
1607) .........................1-14, 2-39
BREAKER CONTROL .......................................................1-19
close breaker 1 ..............................................................1-19
close breaker 2 ..............................................................1-19
remote ...........................................................................1-19
trip breaker 1 .................................................................1-19
trip breaker 2 .................................................................1-19
BREAKER OPERATIONS
maximum number permitted............................................. 2-7
number of ....................................................................... 2-7
BURDEN RATINGS ........................................................... 7-1
BUSLINE (Protection Settin
g
1821) ..........................1-48, 2-44
BYPASSTL3 (Protection Settin
g
902) ................................2-31