GE ALPS - Page 355

GE Power Management
ALPS Advanced Line Protection System iii
INDEX
INDEX
C
C1 (Protection Settin
g
2019) ............................................ 2-46
C2 (Protection Settin
g
2020) ............................................ 2-46
CARRSTART (Protection Settin
g
1204).. 1-30, 2-23, 2-33, 2-60,
2-69
CASE ................................................................................ 3-1
CASE ASSEMBLY ............................................................. 3-1
CC
see CONTACT CONVERTERS
CC1 (General Settin
g
501) ................................................. 2-8
CC10 (General Settin
g
510) ............................................... 2-8
CC11 (General Settin
g
511) ............................................... 2-8
CC12 (General Settin
g
512) ............................................... 2-8
CC2 (General Settin
g
502) ................................................. 2-8
CC3 (General Settin
g
503) ................................................. 2-8
CC4 (General Settin
g
504) ................................................. 2-8
CC7 (General Settin
g
507) ................................................. 2-8
CC8 (General Settin
g
508) ................................................. 2-8
CC9 (General Settin
g
509) ................................................. 2-8
CHANGE BUS/STATION ID............................................ 11-12
CHANNEL RELEASE TIME
definition ....................................................................... 2-34
CHANNEL TEST .............................................................. 8-11
CIRCUIT BOARDS
bus card.......................................................................... 3-3
communications interface ................................................ 3-9
communications interface dia
g
ram ................................... 3-9
DSP/ANI board .............................................................. 3-11
i960 CPU board............................................................. 3-12
input ........................................................................ 3-6, 3-7
local user interface lo
g
ic .................................................. 3-6
locations ......................................................................... 3-3
ma
g
netics module ...........................................................3-3
output ............................................................................. 3-6
power supply................................................................. 3-10
CLOSE BREAKER ............................................................. 8-9
CLOSE BREAKER 1 ........................................................ 1-19
CLOSE BREAKER 2 ........................................................ 1-19
CLOSEANG (Protection Settin
g
1819) ......................1-48, 2-44
CLR KEY ........................................................................... 8-2
COMMUNICATIONS ........................................................ 1-20
ALPS modem ................................................................ 8-25
ASCII command list ....................................................... 12-2
ASCII interface......................................................8-23, 12-1
description .................................................................... 12-1
DNP 3.0 ..........................................................................C-1
interface board ................................................................ 3-9
modem connections/settin
g
s ..................................8-24, 8-25
modem connnections/settin
g
s ........................................ 8-25
null-modem connections ........................................8-23, 8-27
passwords..................................................................... 8-21
remote communications interface ................................... 8-24
software ........................................................................ 8-23
COMPENSATED POSITIVE-SEQUENCE OVERVOLTAGE
application .................................................................... 1-44
description .................................................................... 1-44
phasor dia
g
ram ............................................................. 1-44
COMPENSATED SYSTEMS
Zone 1
g
round reach settin
g
.......................................... 2-11
Zone 1 settin
g
s ............................................................... 2-9
COMPENSATION FACTOR ................................................ 7-2
COMPORT1 (General Settin
g
201) ..................................... 2-4
COMPORT2 (General Settin
g
202) ..................................... 2-5
COMPORT3 (General Settin
g
203) ..................................... 2-5
CONFGTRIP (Protection Settin
g
810) ............................... 2-30
CONFIGURATION
outputs ..........................................................................1-10
CONFOSC (Protection Settin
g
2026)........................ 1-16, 2-47
CONFTRIP (Protection Settin
g
2025) ................................2-47
CONNECTING
to & lo
gg
in
g
out of device ...............................................11-9
CONSTRUCTION ........................................................3-1, 3-6
CONTACT CONVERTERS
calculation of settin
g
s ......................................................2-8
default assi
g
nments .........................................................1-9
di
g
ital output test ...........................................................8-12
input fla
g
s......................................................................13-4
protection settin
g
s ...........................................................2-8
status ............................................................................8-18
CONTACT RATINGS ..........................................................7-1
CONTINUOUS MONITOR .................................................1-22
CONTRAST......................................................................8-15
COUNTERS .....................................................................13-3
CS28A .............................................................................1-30
interconnection dia
g
ram for blockin
g
scheme ..................1-32
CS61C .............................................................................1-23
interconnection dia
g
ram for blockin
g
scheme ..................1-32
CT RATIO
see CURRENT TRANSFORMER RATIO
CTRATIO (Protection Settin
g
1407)...................................2-37
CURRENT SUPERVISION FUNCTION ................................7-1
CURRENT TRANSFORMER RATIO
settin
g
...........................................................................2-37
CURRENT UNBALANCE DETECTION...............................1-16
CURVES
extremely inverse curve .................................................2-50
inverse curve .................................................................2-48
very inverse curve..........................................................2-49
CUSTOM PROGRAMMABILITY ..........................................1-9
D
DATE/TIME
modifyin
g
.........................................................................8-7
DBUSDLINE (Protection Settin
g
1838) ..............................2-45
DBUSLLINE (Protection Settin
g
1837)...............................2-45
DEFTIMDELY (Protection Settin
g
616) ..............................2-27
DELTAV (Protection Settin
g
1839) ...........................1-48, 2-45
DELTAVBLK (Protection Settin
g
1840) .....................1-48, 2-46
DESCRIPTION ...................................................................1-4
DEVICE PROFILE DOCUMENT (DNP 3.0) ......................... C-2
DIGITAL INPUT TEST ........................................................4-9
DIGITAL INPUTS
see CONTACT CONVERTERS
DIGITAL OUTPUTS
power supply board........................................................3-10
test.............................................................................. 11-13
DIGITAL-TO-ANALOG CONVERTER
see SCADA DTA
DIMENSIONS.....................................................................7-2
DISABLE OUTPUTS
with ALPS-Link ............................................................ 11-12
with keypad .....................................................................8-8
DISPLAY
contrast .........................................................................8-15
description.......................................................................8-1
messa
g
es ........................................................................8-3
DISPLAYVAL (General Settin
g
108) ....................................2-4
DISTANCE FUNCTIONS
maximum allowable reach ..............................................2-13
Xpression Builder fla
g
s ..................................................13-6
Zone 1......................................................................1-4, 2-9
Zone 2...........................................................................2-14