GE ALPS - Page 356

iv ALPS Advanced Line Protection System
GE Power Management
INDEX
INDEX
Zone 3.................................................................... 1-4, 2-16
Zone 4...........................................................................2-19
DISTURBANCE PERIOD .................................................. 1-16
DNP
chan
g
in
g
settin
g
s............................................................ C-1
device profile document .................................................. C-2
implementation table ....................................................... C-4
points lists ...................................................................... C-6
DRAWINGS .......................................................................6-2
DTA
see SCADA DTA
DUTY
accumulated duty, phase A ..............................................2-7
accumulated duty, phase B ..............................................2-7
accumulated duty, phase C ..............................................2-7
breaker duty ........................................................... 1-17, 2-7
total duty calculation ........................................................2-7
total duty equation ...........................................................2-6
DWELLTIME (Protection Settin
g
1814).............1-46, 1-47, 2-43
E
ELECTRICAL CONNECTIONS ............................................3-3
ELECTRICAL RATINGS .....................................................7-1
ELEMENTARY DIAGRAMS.....................1-49, 1-50, 1-51, 1-52
ENABLE OUTPUTS
with ALPS-Link ............................................................ 11-12
with keypad .....................................................................8-9
ENCRYPTION
password encryption ...................................................... 8-21
END KEY ...........................................................................8-6
ENT KEY ...........................................................................8-2
ENVIRONMENT .................................................................3-5
EQUIPMENT DUTY .......................................................... 1-17
EQUIPMENT GROUNDING.................................................4-2
ERROR MESSAGES
keypad/display interface.................................................8-22
EVENT
information .................................................................... 8-19
list................................................................................. 8-19
report .......................................................................... 11-15
EXPONENT (General Settin
g
401) ......................................2-7
EXTERNAL CONNECTIONS ...............................................3-5
EXTREMELY INVERSE TOC CURVE
F
FAILURE MESSAGES
960 cpu board .................................................................9-5
ANI / DSP board ..............................................................9-6
communications warnin
g
s ................................................9-5
description.......................................................................9-5
ma
g
netics module............................................................9-5
miscellaneous failures......................................................9-5
miscellaneous messa
g
es..................................................9-6
FAQ.................................................................................. A-1
FAULT
report .......................................................................... 11-15
request fault information ................................................ 8-17
FAULT DETECTOR ......1-16, 1-22, 1-27, 1-30, 1-37, 2-25, 2-31
FAULT LOCATION ........................................................... 1-16
FAULT LOCATION ALGORITHM
line len
g
th ..................................................................... 2-36
FAULT REPORT .............................................................. 1-16
FD
see FAULT DETECTOR
FLAGS
breaker equipment duty alarm.......................................... 2-7
number of breaker operations alarm................................. 2-7
open pole (OPENPOLE) .................................................1-37
sin
g
le phase trip (SINGTRIP)..........................................1-37
FLASH MEMORY..............................................................1-16
FLTLOCK (Protection Settin
g
1501)..........................1-20, 2-37
FLTRESET (Protection Settin
g
1502)........................1-20, 2-37
FREQUENCY
system ............................................................................ 2-2
FREQUENCY SHIFT CHANNEL ........................................1-33
FREQUENTLY ASKED QUESTIONS .................................. A-1
FRONT VIEW .................................................................... 3-2
FSK
see FREQUENCY SHIFT CHANNEL
FUNCTIONAL TESTS
AC system input .............................................................. 6-5
description ............................................................... 5-1, 6-1
di
g
ital outputs ................................................................. 6-4
enterin
g
test mode .......................................................... 6-3
exitin
g
test mode............................................................5-19
factory settin
g
s ............................................................... 5-1
fault detector................................................................... 5-2
g
round directional block (factory settin
g
s) ........................ 5-3
g
round directional block (user settin
g
s) ............................ 6-7
g
round directional trip (factory settin
g
s) ........................... 5-3
g
round directional trip (user settin
g
s) ............................... 6-6
g
round instantaneous overcurrent (factory setttin
g
s)......... 5-4
g
round instantaneous overcurrent (user settin
g
s) ............. 6-8
g
round reach timer test connections................................. 5-7
g
round time overcurrent (factory settin
g
s) ........................ 5-4
g
round time overcurrent (user settin
g
s) ............................ 6-9
g
round timer tests ..........................................................5-11
IB blockin
g
supervision (factory settin
g
s) ......................... 5-3
IB blockin
g
supervision (user settin
g
s) ............................. 6-6
instructions ..................................................................... 6-3
IT trip supervision (factory settin
g
s) ................................. 5-2
IT trip supervision(user settin
g
s) ...................................... 6-6
LUI display test ............................................................... 6-4
LUI relay status ............................................................... 6-4
out-of-step reach ............................................................5-19
overvolta
g
e ..................................................................... 5-5
phase instantaneous overcurrent (factory settin
g
s) ........... 5-4
phase instantaneous overcurrent (user settin
g
s)............... 6-8
phase timer ....................................................................5-16
phase-reach test connections .........................................5-18
phase-to-phase test connections...................................... 5-6
undervolta
g
e test ............................................................ 5-8
user settin
g
s ................................................................... 6-1
Zone 1
g
round reach (factory settin
g
s) ............................. 5-8
Zone 1
g
round reach (user settin
g
s)................................6-12
Zone 1 phase reach (factory settin
g
s) .............................5-13
Zone 1 phase reach (user settin
g
s) .................................6-16
Zone 1-4 phase-to-
g
round calculations............................6-10
Zone 1-4 phase-to-phase reach calculations....................6-14
Zone 2
g
round reach (factory settin
g
s) ............................. 5-9
Zone 2
g
round reach (user settin
g
s)................................6-13
Zone 2 phase reach (factory settin
g
s) .............................5-13
Zone 2 phase reach (user settin
g
s) .................................6-16
Zone 2 timer .........................................................5-11, 5-16
Zone 3
g
round reach (factory settin
g
s) ............................. 5-9
Zone 3
g
round reach (user settin
g
s)................................6-13
Zone 3 phase reach (factory settin
g
s) .............................5-14
Zone 3 phase reach (user settin
g
s) .................................6-17
Zone 3 timer .........................................................5-12, 5-17
Zone 4
g
round reach (user settin
g
s)................................6-14
Zone 4
g
round reach(factory settin
g
s) .............................5-10
Zone 4 phase reach (factory settin
g
s) .............................5-15