GE L90 - Page 895

INDEX
L90 LINE CURRENT DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL xiii
Real-time clock
actual values for synchronization ..............................................6-9
settings ...............................................................................................5-108
Reboot relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-3
Recloser curves ...................................................................5-163, 5-261
Reclosing
logic diagrams ................................................................................5-407
sequence diagram ........................................................................5-411
settings ...............................................................................................5-399
Redundancy
PRP actual values .............................................................................6-11
PRP explained .....................................................................................5-48
settings ..................................................................................................5-46
specifications ......................................................................................2-48
Relay architecture ............................................................................5-187
Relay maintenance ............................................................................... 7-3
Relay name ..........................................................................................5-135
Release Notes .....................................................................................11-14
Remote access of front panel in EnerVista ................. 4-17, 6-3
Remote access, explained ................................................................ 5-9
Remote loopback settings ...........................................................5-432
Remote Setting Authorization ...................................................11-14
Remote terminal FlexAnalogs ..................................................... A-16
Repair ...................................................................................1-2, 11-29, D-1
Replace battery .................................................................................11-24
Replace battery message .................................................................7-9
Replace front panel .........................................................................11-15
Replacement modules ......................................................................2-26
Requirements for installation .......................................................3-51
Reset to factory defaults ....................................................... 5-9, 5-23
Resetting
FlexLogic operands .......................................................................5-202
setting to clear LEDs and messages ....................................5-421
to factory defaults .............................................................................. 5-9
Restart relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-3
Restore settings ....................................................................................11-8
Restraint current FlexAnalogs ..................................................... A-16
Restricted ground fault
actual values .......................................................................................6-27
FlexAnalogs ...........................................................................................A-1
FlexLogic operands .......................................................................5-198
logic diagram ...................................................................................5-285
settings ...............................................................................................5-282
specifications ......................................................................................2-34
Revision history .......................................................................................D-1
RF immunity specifications ............................................................2-52
RFI, conducted specifications .......................................................2-52
R-GOOSE description .........................................................................5-66
RJ-45 ...............................................................................................2-11, 3-11
RMS voltage specifications ............................................................2-43
Roles for login ..........................................................................................2-9
Rolling demand ..................................................................................5-121
Routable GOOSE ...................................................................................5-66
RS232
baud rate .............................................................................................5-43
configuration ...................................................................................... 3-63
specifications .....................................................................................2-48
wiring .....................................................................................................3-29
RS422
configuration ...................................................................................... 3-39
timing .....................................................................................................3-41
two-channel application ..............................................................3-39
with fiber interface ..........................................................................3-42
RS485
description ...........................................................................................3-31
port on rear panel ............................................................................3-11
settings .................................................................................................5-43
specifications .....................................................................................2-48
RTD FlexAnalogs ..................................................................................A-27
RTD inputs
actual values ......................................................................................6-27
settings ...............................................................................................5-423
specifications .....................................................................................2-45
Rules for passwords .............................................................................5-9
RxGOOSE
actual values ......................................................................................6-25
error messages .................................................................................7-11
FlexAnalogs .........................................................................................A-29
settings .................................................................................................5-71
S
Save settings ............................................................................................4-1
Saving setting does not take relay out of service ...............5-1
SCADA protocol selection ...............................................................5-52
SCD file
import ..................................................................................................11-12
import preferences ..........................................................................11-9
SCL compatible ....................................................................................5-58
SCL file import ...............................................................5-75, 5-77, 5-78
preferences .........................................................................................11-9
Security
commands .............................................................................................7-6
delete files and records ...............................................................11-29
EnerVista and UR secure with SSH .............................................2-8
failed authentication lockout .....................................................5-23
forceful user logout ............................................................................7-3
lock FlexLogic equations .................................................................4-9
password for settings template ...................................................4-7
passwords for settings and commands ................... 4-61, 5-11
RADIUS server for user authentication .....................................B-1
role-based user access ....................................................................2-9
settings .................................................................................................5-21
software options ..............................................................................2-50
specifications .....................................................................................2-50
system and event logs ...................................................................5-26
Security audit list of port numbers ........................................... 5-46