GE LPS-O - TABLE AND FIGURES; List of Tables

GE Power Management LPS-O Line Protection System B-
1
APPENDIX B B.1 TABLES
B
APPENDIX B TABLES AND FIGURESB.1 TABLES B.1.1 LIST OF TABLES
T
ABLE
: 1–1 ORDER CODES FOR THE LPS-O........................................................................................................... 1-3
T
ABLE
: 1–2 LPS-O MEASUREMENT FUNCTIONS .................................................................................................... 1-5
T
ABLE
: 1–3 LPS-O DEFAULT CONTACT CONVERTER ASSIGNMENTS................................................................. 1-6
T
ABLE
: 1–4 LPS-O DEFAULT OUTPUT CONTACT ASSIGNMENTS......................................................................... 1-7
T
ABLE
: 1–5 TRUTH TABLE FOR SETTINGS GROUP.............................................................................................. 1-14
T
ABLE
: 1–6 SETTINGS GROUP SWITCH 16SB1_______....................................................................................... 1-14
T
ABLE
: 2–1 TRIPPING SCHEMES .............................................................................................................................. 2-4
T
ABLE
: 2–2 SETTING FORMAT FOR NUM_MON ...................................................................................................... 2-5
T
ABLE
: 2–3 OSCILLOGRAPHY CYCLES PER STORAGE EVENT ........................................................................... 2-7
T
ABLE
: 2–4 FIXED VALUES FOR PROTECTION SETTINGS 503 TO 505.............................................................. 2-14
T
ABLE
: 2–5 INDEX NUMBERS – CONTACT CONVERTER INPUT ASSIGNMENT................................................. 2-32
T
ABLE
: 2–6 INDEX NUMBERS – CONFIGURABLE LOGIC & PROGRAMMABLE OUTPUT SIGNALS.................. 2-33
T
ABLE
: 2–7 PROTECTION SETTINGS GUIDE ......................................................................................................... 2-37
T
ABLE
: 2–8 GENERAL SETTINGS GUIDE................................................................................................................ 2-44
T
ABLE
: 2–9 PROTECTION SETTINGS DATA SHEET.............................................................................................. 2-47
T
ABLE
: 2–10 GENERAL SETTINGS DATA SHEET .................................................................................................. 2-54
T
ABLE
: 3–1 JUMPER POSITION................................................................................................................................. 3-9
T
ABLE
: 4–1 AVAILABLE RELAY TESTS ..................................................................................................................... 4-5
T
ABLE
: 4–2 FACTORY DEFAULT COMMUNICATIONS PARAMETERS................................................................... 4-7
T
ABLE
: 4–3 DIGITAL OUTPUTS TEST CONNECTIONS ..........................................................................................4-12
T
ABLE
: 5–1 TIME-OUT VALUES WHILE REPEATING T8.......................................................................................... 5-6
T
ABLE
: 5–2 FAULT CURRENT PHASE SETTINGS FOR TEST T11........................................................................ 5-10
T
ABLE
: 5–3 FAULT CURRENT PHASE SETTINGS FOR TEST T12........................................................................ 5-11
T
ABLE
: 5–4 FAULT CURRENT PHASE SETTINGS FOR T13.................................................................................. 5-12
T
ABLE
: 5–5 FAULT CURRENT PHASE SETTINGS FOR TEST T14........................................................................ 5-14
T
ABLE
: 5–6 FAULT CURRENT PHASE SETTINGS FOR TEST T17........................................................................ 5-20
T
ABLE
: 6–1 TEST CURRENT RANGES FOR PHASE-TO-PHASE REACH ............................................................... 6-9
T
ABLE
: 8–1 PASSWORD ENCRYPTION KEY TABLE.............................................................................................. 8-24
T
ABLE
: 8–2 KEYPAD / DISPLAY INTERFACE ERROR MESSAGES....................................................................... 8-25
T
ABLE
: 8–3 HARDWARE SWITCH DESCRIPTIONS................................................................................................ 8-27
T
ABLE
: 8–4 COMMAND SEQUENCE SENT BY LPSO-L
INK
TO MODEM................................................................ 8-28
T
ABLE
: 8–5 CONFIGURATION SETTINGS FOR THE MODEM CONNECTED TO THE RELAY............................. 8-29
T
ABLE
: 8–6 MODEM COMMANDS FOR COMMUNICATION BETWEEN RELAY AND PC..................................... 8-31
T
ABLE
: 9–1 COMPONENTS TESTED DURING START-UP TESTS .......................................................................... 9-2
T
ABLE
: 9–2 RUN-TIME BACKGROUND SELF-TESTS............................................................................................... 9-3
T
ABLE
: 9–3 RUN-TIME FOREGROUND SELF-TESTS............................................................................................... 9-3
T
ABLE
: 9–4 SYSTEM STATUS ERROR MESSAGES................................................................................................. 9-4
T
ABLE
: 10–1 INPUT QUANTITIES............................................................................................................................. 10-3
T
ABLE
: 12–1 ASCII PROMPTS.................................................................................................................................. 12-1
T
ABLE
: 12–2 OSCILLOGRAPHY DATA STRUCTURE.............................................................................................. 12-2
T
ABLE
: 12–3 ASCII COMMAND LIST........................................................................................................................ 12-2
T
ABLE
: 13–1 PICKUP DELAY TIMER TRUTH TABLE.............................................................................................. 13-7
T
ABLE
: 13–2 CONTACT CONVERTER INPUT FLAGS............................................................................................. 13-8
T
ABLE
: 13–3 CONFIGURABLE INPUTS.................................................................................................................... 13-9
T
ABLE
: 13–4 SCHEME LOGIC INPUTS .................................................................................................................... 13-9
T
ABLE
: 13–5 CURRENT AND VOLTAGE UNITS...................................................................................................... 13-9
T
ABLE
: 13–6 SCHEME LOGIC OUTPUTS ............................................................................................................. 13-10
T
ABLE
: 13–7 DISTANCE UNITS .............................................................................................................................. 13-11
T
ABLE
: 13–8 MISCELLANEOUS.............................................................................................................................. 13-11
T
ABLE
: 13–9 USER DEFINABLE OUTPUT FLAGS................................................................................................. 13-12