Need help?Do you have a question about the Headsight TRUESIGHT 2 and is the answer not in the manual?
Lists and describes the various components included in the Truesight 2 system, with part numbers.
Explains the main harness and its three legs connecting system components.
Details the specific installation for John Deere 9000 series with a steering motor.
Details the specific installation for John Deere 9000 series with an aftermarket valve.
Outlines general preparation steps before commencing installation.
Describes the connection of safety enable connectors for system operation.
Provides instructions for connecting and orienting the base controller unit.
Details the wiring procedures within the combine cab.
Instructions for connecting the power supply harness.
Instructions for connecting the optional auxiliary switch.
Guides for wiring the system with a Virtual Terminal (VT) display.
Specific wiring instructions for AgLeader InCommand/Integra monitors.
Specific wiring instructions for Trimble FMX, GFX, & TMX monitors.
Instructions for routing wiring outside the combine cab.
Details the procedure for routing wires through the cab access panel.
Optional installation for the feederhouse position sensor.
Instructions for connecting the crop sensor and related wiring.
Instructions for mounting and connecting the GPS unit.
Provides steps for installing the wheel angle sensor.
Wiring instructions for various steering system types.
Wiring instructions for Trimble AutoPilot systems.
Wiring instructions for Ontrac 3 and Ontrac2 motors.
Wiring instructions for the EZ-Pilot motor.
Wiring instructions for the EZ-Steer motor.
Wiring instructions for Outback Bang-Bang and PWM valves.
Wiring instructions for Ag Leader Paradigm and SteadySteer systems.
Guides for installing and adjusting the crop sensor assembly.
Instructions for setting up the system's monitor.
Specific steps for setting up John Deere GS3/2630 monitors.
Specific steps for setting up AgLeader InCommand/Integra monitors.
Specific steps for setting up Trimble FMX, GFX, & TMX monitors.
Guides the user through the initial setup questions upon first power-up.
Explains how to access the calibration menu on the VT display.
Calibrates the connector orientation for slope compensation.
Calibrates the maximum motion and direction of the wheel angle sensor.
Adjusts the centering reference for the row guidance.
Calibrates the current required to start wheel turning.
Sets the auto engage/disengage position based on feederhouse height.
Calibrates the 'straight ahead' position of the wheel angle sensor.
Guides the user to access and adjust system settings.
Configures basic system parameters like machine type and steering.
Sets the combine's type and manufacturer.
Configures the specific steering system being used.
Configures how the system reads speed for safety features.
Configures the external engage input, like a foot switch.
Adjusts core operating parameters for steering response.
Adjusts the aggressiveness of the Truesight system's steering.
Fine-tunes steering response for curves.
Compensates for combine tilt on slopes.
Fine-tunes steering parameters like deadzones and gain.
Manually adjusts the valve/motor deadband.
Controls the speed of steering response based on error.
Smooths the transition when starting to turn the wheels.
Dampens small overshoots in steering.
Guides on how to find and access the Truesight application.
Specific steps for operating Truesight on JD monitors.
Specific steps for operating Truesight on Ag Leader/Trimble monitors.
How Truesight 2 interacts with Horizon header height control.
Lists the conditions that must be met before Truesight can engage.
How to use and manage Road Mode for safe transport.
Step-by-step guide on how to engage the Truesight system.
Instructions on how to safely disengage the Truesight system.
How to use the bump steer function for minor adjustments.
Explains the meaning of different LED blink sequences.
Instructions for updating software using the Techlink mobile app.
Instructions for updating software via a USB flash drive.
Explains how the Truesight 2 system functions and its components.
Overview of accessing and viewing diagnostic information.
Steps to navigate to and open diagnostic menus.
Displays current sensor voltages and system status.
Shows reasons for system disengagement and safeties status.
Provides reference to power, inputs, and outputs on the 40-pin connector.
Allows testing the steering command response.
General guidance on resolving system issues.
Diagnosing issues related to sensors and wiring.
Resolving problems based on observed system behavior.
Diagnosing issues based on specific error codes displayed.
Wiring diagram for the main TS-TRUNK harness.
Wiring diagram for the power adapter.
List of parts for the crop sensor assembly.
List of parts for the wheel angle sensor assembly.
General| Brand | Headsight |
|---|---|
| Model | TRUESIGHT 2 |
| Category | Farm Equipment |
| Language | English |
To Next Page
