Hengstler eXtendo X-80 - Table of Contents

eXtendo
®
Em ulation Command Set Reference
Part No. D 684 112 Mod.Nr. 4 150813 LEV Page 5 of 95
Table of Contents
1 Introduction .......................................................................................................... 7
2 Printer Command Overview (Emulation) ........................................................... 8
2.1 Emulation Command Set ........................................................................................................ 8
2.1.1 HT Horizontal tab .............................................................................................................. 9
2.1.2 LF Line feed ....................................................................................................................10
2.1.3 CR Carriage Return .........................................................................................................11
2.1.4 FF Form Feed (new page) ..............................................................................................12
2.1.5 CAN Cancel (reset print engine) .....................................................................................13
2.1.6 ESC % +[n] Character set selection ................................................................................14
2.1.7 ESC ! +[n] Character size specification ...........................................................................15
2.1.8 GS B + [n] Black-on-white reversed printing specification...............................................16
2.1.9 ESC 2 1/6-inch line pitch setting .....................................................................................17
2.1.10 ESC 3 +[n] Line pitch setting ..........................................................................................18
2.1.11 ESC A+[n] Line spacing setting .......................................................................................19
2.1.12 GS L+[n]+[m] Left margin specification ...........................................................................20
2.1.13 ESC SP+[n] Character spacing specification ..................................................................21
2.1.14 ESC ‘-‘+[n] Character underlining ....................................................................................22
2.1.15 ESC ‘E‘+[n] Bold characters enable/disable ....................................................................23
2.1.16 ESC ‘^‘+[n] Print character as graphic .............................................................................24
2.1.17 ESC ‘\‘+[n1]+[n2] Print Character 1-351 ..........................................................................25
2.1.18 ESC ‘%‘+[n] Character Set and Country Code Selection ................................................26
2.1.19 ESC [F0]+[07]+[01]+[n] Enable wide font printing ............................................................28
2.1.20 ESC [F1]+[01]+[03]+[0A]+[n] Page length setting ............................................................30
2.1.21 ESC [F0]+[06]+[x]+[n]+[m] End of page ...........................................................................31
2.1.22 ESC D+[d1]..[dn]+NUL Horizontal tab positions ...............................................................33
2.1.23 ESC J+[n] Forward paper feed .........................................................................................34
2.1.24 ESC d+[n] Forward n-line feed .......................................................................................35
2.1.25 ESC [F2] [04] [00] Position Stamp Set ............................................................................36
2.1.26 ESC [F2] [05] [02] [n1] [n2] Position Stamp Feed.............................................................37
2.1.27 ESC [F2] [06] [02] [n1] [n2] Position Stamp Retract .........................................................38
2.1.28 ESC [F2] [09] [01] [n] Paper Eject.....................................................................................39
2.1.29 ESC a [n] Horizontal Alignment Command ....................................................................40
2.1.30 ESC $ + [n1] + [n2] + [m1] + [m2] Set position .................................................................41
2.1.31 ESC V+[n]+[m] Text, image, bar code and character rotation .........................................42
2.1.32 ESC [F0]+[0B]+[01]+[n] Start block rotation .....................................................................43
2.1.33 ESC [F0]+[0C]+[00] End block rotation ...........................................................................44
2.1.34 ESC @ Printer reset (software) ......................................................................................45
2.1.35 ESC+[F2]+[03]+[00] Printer reset (hardware) ...................................................................46
2.1.36 GS '+[m]+[n] Print stored image data ..............................................................................47
2.1.37 GS e+[n]+[m] Bar code bar width setting .........................................................................48