8-2
BASIC MANUAL
SET MODE
8
8
Tone Control/TBW
»
SET > Tone Control/TBW > RX
SSB, AM, FM, DV, CW, RTTY
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio
high-pass filter and low-pass filter, in 100 Hz steps.
LIf this item is set, the “RX Bass” and “RX Treble”
items are automatically set to “0.”
SSB, AM, FM, DV, WFM
RX Bass (Default: 0)
RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
»
SET > Tone Control/TBW > TX
SSB, AM, FM, DV
TX Bass (Default: 0)
TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio.
SSB
TBW (WIDE) (Default: 100 – 2900)
TBW (MID) (Default: 300 – 2700)
TBW (NAR) (Default: 500 – 2500)
Sets the transmission passband width to wide,
mid, or narrow, by changing the lower and
upper cut-off frequencies.
SSB-D
TBW (WIDE) (Default: 300 – 2700)
Sets the transmission passband width by
changing the lower and upper cut-off frequencies.
Beep Level Limit (Default: ON)
Selects whether or not to limit the volume up to
a specified level.
• OFF: Does not limit the volume level.
• ON: Limits the volume level.
Beep (Confirmation) (Default: ON)
Turns the Confirmation beep ON or OFF.
• OFF:
Turns OFF the function for silent operation.
• ON: A beep sounds when a switch is pushed
or the touch panel is touched.
LIf “Beep Level” is set to “0%,” no beep sounds.
Home CH Beep (Default: ON)
Turns the Home CH Beep ON or OFF.
LIn the VFO or Memory mode, when the Home
Channel frequency or the Home Channel Memory
is selected, the Home CH Beep sounds.
LIn the DR screen, when the Home Channel Access
repeater is set in FROM, the Home CH Beep sounds.
• OFF: No beep sounds.
• ON: Sounds a beep when you select the
Home Channel.
Band Edge Beep (Default: ON (Default))
Selects an option for the Band Edge Beep function.
• OFF: Turns OFF the function.
• ON (Default):
A beep sounds when you tune
out of, or back into the default
amateur band’s frequency range.
• ON (User):
A beep sounds when you tune out
of, or back into a user programmed
amateur band’s frequency range.
• ON (User) & TX Limit:
A beep sounds when you tune
out of, or back into a user
programmed amateur band’s
frequency range. Transmitting
is inhibited outside of the range.
LIf “Beep Level” is set to “0%,” no beep sounds.
Auto Power OFF (Default: OFF)
Selects whether or not to automatically turn OFF the
transceiver after inactivity for this set period of time.
L“AUTO POWER OFF” is displayed and beeps sound
5 seconds before turning OFF the transceiver. If you
operate the transceiver during this period of time,
the Auto Power OFF timer is reset.
• OFF: Does not turn OFF the transceiver.
• 30/60/90/120min:
Turns OFF the transceiver after
inactivity for this set period of time.
NOTE: The default settings shown below
are for the USA transceiver version. The
default settings may differ, depending on your
transceiver version.
Function
»
SET > Function
Beep Level (Default: 50%)
Sets the beep output level.
L If “Beep (Confirmation)” is set to “OFF,” no beeps sound.
To Next Page
Loading...
