Icom IC-705 - The Assignable Key Functions

8-7
BASIC MANUAL
8
SET MODE
Function Description
--- No function
UP
Push to increase the frequency (in 50 Hz
steps*), Memory channel, repeater, or
select the next station call sign.
* When the Tuning Step function is ON,
increases the frequency in the selected
Tuning Step.
DOWN
Push to decrease the frequency (in 50 Hz
steps), Memory channel, repeater, or select
the previous station call sign.
* When the Tuning Step function is ON,
increases the frequency in the selected
Tuning Step.
UP
(VFO: kHz)
Push to increase the frequency (in the
selected Tuning Step), Memory channel,
repeater, or select the next station call sign.
DOWN
(VFO: kHz)
Push to decrease the frequency (in the
selected Tuning Step), Memory channel,
repeater, or select the previous station call
sign.
VOL UP Push to increase the volume level.
VOL DOWN Push to decrease the volume level.
XFC Hold down for 1 second to monitor signals.
CALL Push to select the Call channel mode.
VFO/MEMO
• Push to select the VFO mode and the
Memory mode.
• Hold down for 1 second to copy a
Memory channel contents to the VFO.
DR Push to turn the DR function ON or OFF.
FROM/TO
(DR)
In the DR screen
Push to select “FROM” or “TO.”
Home CH
Push to directly select the Home Channel
that is set to the selected mode (VFO/
Memory) or DR screen.
L While in the Call channel mode, or
when no Home CH is set, an error beep
sounds.
BAND/
GROUP
UP
In the VFO mode
• Push to increase an operating band.
• Hold down for 1 second to recall the
Band Stacking Register contents.
In the Memory mode
Push to increase the Memory group.
BAND/
GROUP
DOWN
In the VFO mode
• Push to decrease an operating band.
• Hold down for 1 second to recall the
Band Stacking Register contents.
In the Memory mode
Push to decrease the Memory group.
SCAN
• Push to start the previously selected
scan. While scanning, push to stop the
scan.
• Hold down for 1 second to open the
SCAN SELECT screen.
Function Description
Temporary
Skip
Push to set the frequency to be skipped
while scanning.
The selected frequencies are temporarily
skipped for faster scanning.
SPEECH
Push to announce the frequency, operating
mode, or call sign.
L In the VFO, Memory, or Call channel
mode, the frequency and the operating
mode are announced.
L In the DR screen, the call sign is
announced. If Simplex is selected, the
frequency is announced.
MODE
• Push to select the operating mode.
• Hold down to toggle USB and LSB, CW
and CW-R, or RTTY and RTTY-R.
RF Power Push to adjust the transmit output power.
Voice TX
(T1)
• Push to transmit the voice audio
recorded on the microSD card once.
• Hold down for 1 second to repeatedly
transmit the voice audio.
L This key function can also be used on
the DR screen.
L If the voice audio is not saved in the
Voice TX memory (T1 or T2), this
function is disabled.
Voice TX
(T2)
Keyer
Memory
(M1)
• Push to transmit the Keyer memory
contents once.
• Hold down for 1 second to repeatedly
transmit the memory contents.
L If the Keyer memory contents (M1
or M2) is not entered, this function is
disabled.
Keyer
Memory
(M2)
T-CALL
Push to transmit a 1750 Hz Tone.
(Only for European version.)
RX>CS
• Push to display the RX History list.
• Hold down for 1 second to set the
last calling station’s call sign to “TO”
(destination).
TS
• Push to turn the Tuning Step function ON
or OFF.
• Hold down for 1 second to open the TS
screen.
MPAD
• Push to sequentially call up the contents
in the Memo Pads.
• Hold down for 1 second to save the
displayed contents into the Memo Pad.
SPLIT
• Push to turn the Split function ON or
OFF.
• Hold down 1 second to turn ON the
Quick Split function.
A/B
• Push to select the VFO A or VFO B.
• Hold down for 1 second to set the
displayed VFO’s frequency to the VFO
that is not displayed.
The assignable key functions