11
SET MODE
11-3
SPEECH > SPEECH Output for Ext connectors
(Default: All)
Selects the announcement condition to output from
the external terminals (USB, LAN, AF/IF and EXT-SP).
• OFF: The announcement is not output.
• Push/Touch: The announcement is output when you
push
, or touch the screen.
• All: The announcement is output when you
push or touch the screen, or when
a signal is received during a scan.
L The announcement is not output if [S-Level SPEECH],
[MODE SPEECH] or [SCAN SPEECH] is set to “OFF.”
SPEECH >
SPEECH Output for Recording
(Default: All)
Selects the announcement recorded condition.
• OFF: The announcement is not recorded.
• Push/Touch: The announcement is recorded when
you push
, or touch the screen.
• All: The announcement is recorded when
you push or touch the screen, or
when a signal is received during a scan.
L The announcement is not recorded if [S-Level SPEECH],
[MODE SPEECH] or [SCAN SPEECH] is set to “OFF.”
SPEECH >
SPEECH Level (Default: 50%)
Sets the announcement output level.
• Range: 0 ~ 100%
[SPEECH/LOCK] Switch (Default: SPEECH/LOCK)
Selects the
key action.
• SPEECH/LOCK: Pushing turns ON the Speech
function.
Holding down turns the Lock
function ON or OFF.
• LOCK/SPEECH: Pushing turns the Lock
function ON or OFF.
Holding down turns ON the
Speech function.
[P.LOCK] Switch (Default: ALL)
Selects the action of the
key.
L and are not locked.
• ALL: All controls are disabled.
• KEY:
All controls except and
are disabled.
L When you hold down for 1 second, the display
backlight is turned OFF.
L
When “KEY” is selected and while the Panel Lock is
activated, rotating
or turns ON the display
backlight.
MAIN DIAL Auto TS (Default: High)
Sets the Auto Tuning Step function for
.
When rapidly rotating
, the tuning step
automatically changes according to the rotation speed.
• OFF: Auto tuning step is turned OFF.
• LOW: Approximately 2 times faster.
• HIGH: Approximately 5 times faster when the tuning
step is set to 1 kHz or smaller steps.
Approximately 2 times faster when the tuning
step is set to 5 kHz or larger steps.
AFC Limit (Default: ON)
Selects whether or not to limit the frequency shift
range for the AFC function.
• OFF: Does not limit the frequency shift range.
• ON: Limits the frequency shift range according to
the table below.
Receive mode Filter width AFC range limit
DIGITAL 5 kHz
±3.5 kHz
10 kHz
±7 kHz
FM/DIGITAL 7 kHz
±5 kHz
15 kHz
±10 kHz
FM 50 kHz
±25 kHz
WFM 200 kHz
±100 kHz
[NOTCH] Switch (AM) (Default: Auto/Manual)
[NOTCH] Switch (SSB) (Default: Auto/Manual)
Selects the Notch function type in the SSB or AM mode.
• Auto: Only the Auto notch lter (AN).
• Manual: Only the Manual notch lter (MN).
• Auto/Manual: Both the Auto and Manual notch lters.
SSB/CW Synchronous Tuning (Default: OFF)
Turns the Displayed Frequency Shift function ON or OFF.
This function automatically shifts the frequency to
match the CW pitch when the operating mode is
toggled between SSB and CW.
• OFF:
Stays on the frequency even when the operating
mode is toggled between SSB and CW.
• ON: Shifts the frequency when the operating mode
is
toggled
between SSB and CW, to keep
receiving the signal.
CW Normal Side (Default: LSB)
Selects the carrier point in the CW normal mode.
• LSB: The LSB side.
• USB: The USB side.
Screen Capture [POWER] Switch (Default: OFF)
Assigns the Screen Capture function to
.
• OFF:
does not act as the Screen Capture key.
• ON: acts as the Screen Capture key.
Function (Continued)
To Next Page
Loading...
