11
SET MODE
11-5
Connectors
Phones Level Ratio (Default: 1.00)
Sets the output ratio of the speaker output level and
headphones output level.
• Range: 0.40 ~ 2.00
AF/IF > Output Select (Default: AF)
Selects the signal output from [AF/IF].
• AF: The demodulated AF signal is output.
• IF: A 12 kHz IF signal is output.
L You can listen to the Digital Radio Mondiale (DRM)
broadcast with an application software receiver if it
is installed into your PC.
AF/IF >
AF Output Level (Default: 50%)
Sets the AF output level of [AF/IF].
• Range: 0 ~ 100%
L At 50% (default), the output level is 200 mV (RMS).
AF/IF >
AF SQL (Default: OFF (OPEN))
Selects whether or not to output the audio from [AF/IF],
according to the squelch and signal levels.
• OFF(OPEN):
The squelch is always opened regardless
of the squelch and signal levels.
• ON:
The squelch opens and closes, according
to the squelch and signal levels.
AF/IF > AF Beep/Speech... Output (Default: OFF)
Sets the Beep and Speech audio output status of [AF/IF]
.
• OFF: The beep and speech audio are not output
from [AF/IF].
• ON: The beep and speech audio are output from
[AF/IF].
AF/IF > IF Output Level (Default: 50%)
Sets the IF output level of [AF/IF].
• Range: 0 ~ 100%
L At 50% (default), the output level is 200 mV (RMS).
USB (Front) >
Output Select (Default: AF)
Selects the signal output from [USB] on the front panel.
• AF: The demodulated AF signal is output.
• IF: A 12 kHz IF signal is output.
L You can listen to the Digital Radio Mondiale (DRM)
broadcast with the application software receiver that
is installed into your PC.
USB (Front) >
AF Output Level (Default: 50%)
Sets the AF output level of [USB] on the front panel.
• Range: 0 ~ 100%
» SET > Connectors
USB (Front) > AF SQL (Default: OFF (OPEN))
Selects whether or not to output the audio from [USB] on
the front panel, according to the squelch and signal levels.
• OFF(OPEN):
The squelch is always opened regardless
of the squelch and signal levels.
• ON:
The squelch opens and closes, according
to the squelch and signal levels.
USB (Front) > AF Beep/Speech... Output
(Default: OFF)
Sets the Beep and Speech audio output status of
[USB] on the front panel.
• OFF: The beep and speech audio are not output
from [USB] on the front panel.
• ON: The beep and speech audio are output from
[USB] on the front panel.
USB (Front) > IF Output Level (Default: 50%)
Sets the IF (12 kHz) output level of [USB] on the front
panel.
• Range: 0 ~ 100%
USB (Front) > Serial Function (Default: FSK Decode)
Selects the signal output from [USB] on the front panel.
• FSK Decode: An FSK decoded signal is output.
• D-STAR Data: A D-STAR data is output.
USB (Front) > FSK Decode Baud Rate (Default: 9600)
Selects the data transfer rate (Baud rate) of decoded
FSK signals from [USB] on the front panel.
• Options: 4800, 9600, 19200 or 38400 (bps)
USB (Front) > D-STAR Data Baud Rate (Default: 9600)
Selects the data transfer rate (Baud rate) of decoded
D-STAR data
from [USB] on the front panel.
• Options: 4800 or 9600 (bps)
USB (Rear) > Output Select (Default: AF)
Selects the signal output from [USB] on the rear panel.
• AF: The demodulated AF signal is output.
• IF: A 12 kHz IF signal is output.
L You can listen to the Digital Radio Mondiale (DRM)
broadcast with the application software receiver that
is installed into your PC.
USB (Rear) >
AF Output Level (Default: 50%)
Sets the AF output level of [USB] on the rear panel.
• Range: 0 ~ 100%
L At 50% (default), the output level is 200 mV (RMS).
To Next Page
Loading...
