30 Installation
Anti-intrusion control panels
3-1-4
Thermal probe
The thermal probe [D] optimizes the battery charge process. This device regulates the
charging process in accordance with the battery temperature. The thermal probe
protects against battery overheating and consequent permanent damage to the battery.
To connect a thermal probe, work through the following steps.
1. Disconnect the battery (if necessary).
2. Connect the thermal probe to the connector on the power supply [E].
For control panels equipped with transformers (SmartLiving 505 and 515), it is
necessary to connect the probe directly to the connector on the motherboard
(Table 2-8: Mother board - description of parts, C).
3. If you are installing a SmartLiving505 or 515 model, remove the jumper on the
motherboard to enable the thermal probe (refer to Table 2-8: Mother board -
description of parts, D).
4. Using adhesive-insulating tape, attach the thermal probe to the battery [F], in
such a way as to provide optimized heat-transfer measurements.
3-1-5
Opening and closing the control panel
If you wish to remove the metal frontplate, work carefully through the following steps.
1. Type-in the installer code on the keypad and press . Access to the installer
menu inhibits the activation of the output and any report calls associated with the
“Open-panel” event.
2. Remove the four screws and the metal-frontplate.
3. Insert the Maintenance jumper (refer to paragraph 3-1-9 Maintenance status)
and carry out the necessary work.
Once your task is complete, work carefully through the following steps.
1. Remove the Maintenance jumper.
2. Using the 4 screws, secure the frontplate to the backbox.
3. Exit the Installer menu.
Note
If you exit the Installer menu before replacing the panel frontplate, the system panel will not
generate an open-panel event.
However, the system will generate an open-panel event, if the frontplate is not replaced within 15
seconds of closing the open-tamper microswitch.
3-1-6
Land-line connection (PSTN)
Connect the land line (PSTN) to terminals 4 and 5 on the control panel motherboard
(Table 2-9: Mother board - terminal board, 4-5).
In order to protect the control panel against the discharge of atmospheric electricity,
(lightning), the manufacture strongly advices the use of the two varistors (150VRM)
included in the package. These varistors must be connected to the earth line 1 and
terminals 4 and 5 of the landline (PSTN).
If you are installing the system in a place where the land line (PSTN) service is not
available, or if you wish to increase the level of security of the system, these terminals
also accept a GSM interface (such as SmartLink) which simulates the analogue land-
line.
Inim's SmartLinkAdv telephone dialler is available in two versions, model G and model
GP. Both devices monitor the analogue land line and in the event line-down conditions
(e.g. wire-cutting) simulate the analogue land line and allow the control panel to switch
incoming/outgoing calls to the GSM network.
You can also use the terminals on the SmartLinkAdv board to extend the functions
provided by the SmartLiving system. The following section describes several methods
which will allow you to provide users with advanced functions.
• Arming/Disarming the system over-the-phone using a cost-free call or SMS text
By connecting one of the SmartLiving board terminals with “follow zone”
configuration to an output on the SmartLinkAdv board, it will be possible to arm or
disarm the SmartLiving system via SMS.
In a similar way, using a “switching zone” configured terminal, it will be possible to
arm or disarm the SmartLiving system simply by means of a recognized incoming
call.
• Receive an SMS text in the event of Control panel alarm
By connecting one of the alarm outputs of the SmartLiving control panel to an input
on the SmartLinkAdv board, it will be possible to receive alarm warning via SMS
text. The system can be set up to send an editable SMS text to 10 different contact
numbers.
To Next Page
Loading...
