Figure E-9. Heatsink Module Clip (Fabric), 1/2
13
4
5678
B
C
D
A
123
4
5678
B
C
D
A
A
2200 MISSION COLLEGE BLVD.
P.O. BOX 58119
SANTA CLARA, CA 95052-8119
R
0.3 A B C
0.25 A B C
0.25 A B
0.25 A
0.2
2X 2.35 0.1
2X 4.75 0.1 2X 4.75 0.1
2X 8.2 0.1
5 0.1
7 0.1
2X 68
80±0.1
2X 95
9.5
107±0.1
8X 6 0.1
3X 6.5 0.1
3X 2 0.1
H53248 1 09
DWG. NO SHT. REV
SHEET 1 OF 2
DO NOT SCALE DRAWING
SCALE: 2:1
09H53248D
REV
DRAWING NUMBER
SIZE
KNL CPU CARRIER (HFI)
TITLE
DEPARTMENT
SEE NOTESSEE NOTES
FINISHMATERIAL
-
DATEAPPROVED BY
3/4/14
DATECHECKED BY
3/4/14
DATEDRAWN BY
08/15/13
DATEDESIGNED BY
DIMENSIONS ARE IN MILLIMETERS
THIRD ANGLE PROJECTION
REVISION HISTORY
ZONE REV DESCRIPTION DATE APPR
- 01 TOOLING RELEASE 3/29/15
PG1 7-A
PG2 7-C
PG1 8-C
PG2 8-C
02
1. REMOVED XHATCHING ON PART.
2. CHANGED PRODUCTION TO PRE-PRODUCTION.
3. ADDED NOTE 8 FOR SYMBOL CALL OUT.
4. ADDED NOTE 4 CALLOUT TO BOTTOM VIEW.
5. ADDED DRAFT
6. ROLLED PART NUMBER FROM -001 TO -002.
4/1/15
03
1. ADDED NOTE 9 TO CALL OUT CRITICAL TO FUNCTION DIMENSION.
2. ADDED POSITION TOLERANCE TO DIAMETER HOLES.
4/23/15
04 1. REMOVED CTF CALLOUT TO BASIC DIMENSIONS. 5/21/15
05 1. ADDED CTF TO WIDTH AND LENGTH PROFILE 6/29/15
PG2 B-7
PG1 B-1
PG1 B-2
06
1. UDPATED COSTMETIC REV ON PART TO MATCH DRAWING REV
2. UPDATED HOLES TRUE POSTION TOLERANCE FROM 0.1 TO 0.25
3. UPDATED PROFILE FROM .125 TO 0.2
10/20/15
PG1 C-1
PG2 C-6
07
1. CHANGED TRUE POSITION TOLERANCE FROM 0.1 TO 0.3
2. REMOVED PROFILE DIMENSION.
2/11/16
PG1 D-7
PG2 B-7
PG2 A-4
PG2 B-5
PG1 C-2
PG1 C-1
PG1 C-3
08
1. REMOVED NOTE #4F TO ELIMINATE THE REVISION OFF THE PART.
2. ADDED A LARGE VISIBLE SCREWDRIVER SYMBOL FOR TIM BREAKER.
3. ADDED ROUNDS TO LATCH FEATURES.
4. ADDED NOTE #11.
5. CHANGED COSMETIC TEXT FROM PUSH TO LATCH ALONG WITH ARROWS.
6. REMOVED CTF SYMBOLS FROM GUIDE POST HOLES.
7. INCREASED SIZE OF PIN 1 TRIANGLE HOLE.
8. ROLLING PART NUMBER FROM H53248-002 TO H53248-003.
6/3/16
PG1 A2
PG2 B7
09
1. REMOVED TWO CTF DIMENSIONS ON PAGES 1 AND 2.
2. REMOVED COSMETIC TEXT "PRE-PRODUCTION".
7/18/16
NOTES; UNLESS OTHERWISE SPECIFIED:
1. REFERENCE DOCUMENTS
ASME Y14.5M-2009 - STANDARD DIMENSION AND TOLERANCES
UL 94 - UL FLAMABILITY TESTING
164997 - INTEL MARKING STANDARD
ISO-11469 - MATERIAL MARKING STANDARD
BS-MTN-0001-INTEL ENVIRONMENTAL PRODUCT SPECIFICATION
2. FEATURES NOT SPECIFIED ON DRAWING SHALL BE CONTROLLED BY 3D CAD
FOR FEATURES NOT EXPLICITLY TOLERANCED:
(BASIC DIMENSIONS FROM 3D CAD MODEL).
3. MATERIAL: MAY USE INTEL ENGINEERING APPROVED EQUIVALENT.
A) TYPE: PC-ABS
B) COLOR: BLACK PER INTEL COLOR MATCHING SPECIFICATION (610204).
C) MINIMUM UL FLAMMABILITY RATING 94-V0
D) MUST BE UL RECOGNIZED MATERIAL.
E) 15% REGRIND ALLOWED.
F) MUST WITHSTAND 120
C WITHOUT DEFORMING
4 MARK PART APPROXIMATELY WHERE SHOWN PER INTEL MARKING
STANDARD (164997) WITH THE FOLLOWING INFORMATION.
MARKING SHOULD BE ENGRAVED INTO PART USING AN INSERT IN THE TOOL SO THAT
INFORMATION CAN BE EASILY CHANGED.
OTHERWISE, BAG AND TAG WITH THE FOLLOWING INFORMATION.
(NOTE PRIORITY IN ORDER LISTED)
A) SUPPLIER PART NUMBER
B) INTEL PART NUMBER: H53248-003
C) CAVITY NUMBER (IF APPLICABLE)
D) DATE CODE
5. DEGATE: FLUSH TO -0.25 MM [-.010"].
6. EJECTOR MARKS: FLUSH TO MINUS 0.0 MM/-0.125 MM [.000 IN/-.005 IN].
7. SHARP CORNERS MAY BE CHAMFERED, OR ROUNDED TO 0.25MM (.010") RADIUS,
UNLESS OTHERWISE SPECIFIED.
8 MARK SYMBOL APPROXIMATELY WHERE SHOWN PER INTEL MARKING
STANDARD (164997) WITH THE FOLLOWING INFORMATION.
MARKING SHOULD BE ENGRAVED INTO PART USING AN INSERT IN THE TOOL.
9. DIMENSIONS MARKED ARE CRITICAL TO FUNCTION DIMENSIONS (CTF).
10 MEASURE IN RESTRAINED XHATCH LOCATIONS WITH 2-5 NEWTONS.
11 MARK SYMBOL APPROXIMATELY WHERE SHOWN PER INTEL MARKING
STANDARD (164997) OPTIONAL.
0.2ABC
PIN 1 INDICATOR
10
C
B
C
C
PARTS LIST
DESCRIPTIONPART NUMBER
ITEM NO
QTY
KNL CPU CARRIER (NON-HFI)H53248-003TOP
To Next Page
Loading...
Need help?
General
