How to fix weak printout on Intermec EasyCoder PD41?
If the printout from your Intermec Printer is weak, check the following: * Density setting. * If the thermal printhead needs cleaning. * Printhead pressure. * Printhead dot line position.
How to fix Intermec EasyCoder PD41 Printer when ribbon is empty?
General| Print technology | Direct thermal |
|---|---|
| Maximum resolution | 203 x 203 DPI |
| Standard interfaces | RS-232, USB 2.0 |
| Internal memory | 16 MB |
| Power requirements | 100-240 VAC ±10%, 45-65 Hz |
| Media thickness | 2.3 - 9.8 mm |
| Maximum label width | 104 mm |
| Maximum label length | 0.15 m |
| Maximum roll diameter | 213 mm |
| Maximum internal memory | 1 GB |
| Supported network protocols | TCP/IP, LPR/LPD, FTP, BOOTP, DHCP, HTTP, SNMPv3, SMTP, SNMP-MIB II |
| Operating temperature (T-T) | 40 - 104 °F |
| Operating relative humidity (H-H) | 20 - 85 % |
Weight and Dimensions| Depth | 453 mm |
|---|---|
| Width | 273 mm |
| Height | 270 mm |
| Weight | 13000 g |
Provides a detailed overview of the EasyCoder PD41 printer's features and capabilities.
Instructions for safely unpacking the printer and its included accessories.
Details on locating and understanding the machine and serial number labels on the printer.
Illustrates and labels the front panel components of the EasyCoder PD41 printer.
Explains the function of the front panel LEDs and the Print button.
Diagram showing the rear panel of the printer and its various ports and connectors.
Details the available connection sockets on the rear of the printer.
Illustrates the internal media compartment of the printer.
Diagram showing the internal print mechanism of the printer.
Step-by-step guide for setting up and connecting the printer.
Guidance on connecting the printer via USB, Serial, Network, or Parallel interfaces.
Procedure to print a test label for verifying printer functionality and configuration.
Instructions for loading various types of media into the printer.
Describes how to use the printer for manual tear-off of printed labels.
Explains the procedure for self-adhesive labels where the liner is separated.
Step-by-step guide for loading thermal transfer ribbon into the printer.
Details the printer states indicated by LEDs and the functions of the Print button.
Provides recommendations for regular inspection and care of the printer.
Instructions on how to clean the printer's printhead to maintain print quality.
Guidance on cleaning the printer's media compartment to prevent jams.
Instructions for cleaning the exterior of the printer to prevent dust ingress.
Lists common printer operation issues and their potential solutions.
Details issues affecting print quality and how to resolve them.
Explains the meaning of the Ready-to-Work LED status and troubleshooting tips.
Provides detailed solutions for common printer adjustments and issues.
Guides on how to adjust ribbon tension and shield to prevent wrinkling.
Step-by-step instructions for clearing media jams from the print mechanism.
Covers adjustments for printhead balance, pressure, and dot line alignment.
Instructions for adjusting the label gap sensor position for accurate media detection.
Describes the printer's startup process and how firmware affects it.
Methods for modifying printer configuration via PrintSet, Home Page, or Command Line.
Explains how to use Testmode and Extended Testmode for diagnostics and setup.
Procedure for downloading and installing the latest printer firmware updates.
Lists detailed technical specifications, including physical dimensions and power.
A comprehensive table detailing the printer's physical, power, printing, and firmware specs.
Specifies the required dimensions for media rolls, including core and roll diameter.
Details the required dimensions for thermal transfer ribbon rolls.
Describes various paper types and their specific width and length requirements.
Specifies media width and paper type setup for non-adhesive strips.
Details media width, liner requirements, and setup for self-adhesive strips.
Covers media width, liner, label width, length, and gap specifications for labels.
Specifies dimensions and detection requirements for tickets with gaps.
Details specifications for tickets and marks used for detection.
Overview of setup parameters and how they affect printer behavior.
Configuration options for serial communication parameters like Baud Rate and Parity.
Parameters controlling media feed before and after printing, including Start and Stop Adjust.
Parameters for configuring media size, type, and print window settings.
Settings related to print speed, contrast, and testfeed modes.
Overview of setup parameters for IPL firmware and their functions.
Information on printing test labels for software, hardware, and network settings.
Configuration of serial communication parameters for IPL firmware.
Parameters for media characteristics like type and sensitivity number.
Settings for emulation, print speed, cutter, and label taken sensor.
Procedure to restore printer settings to factory defaults.
Details the RS-232 serial interface, protocol, and pinout.
Information on using the USB interface, including driver requirements.
Describes the EasyLAN Ethernet interface, its speed, and status LEDs.
Details the Parallel IEEE 1284 interface and its pinout.
Adds network capability to the printer.
Adds a parallel port to the printer.
Enables cutting of continuous paper stock or liner between labels.
Device for peel-off operation and rolling up label batches.
Replacement or complete kit for 203dpi or 300dpi printheads.
To Next Page