Introduction CP3003-SA
Page 1 - 4 ID 1052-6929, Rev. 3.0
D R A F T — F O R I N T E R N A L U S E O N L Y
Some of the CP3003-SA's outstanding features include:
• Support for the following 3
rd
generation processors:
•
Intel® Core™ i7-3612QE (SV) quad-core processor, 2.1 GHz, 6 MB L3 cache
• Intel® Core™ i7-3555LE (LV)
dual-core processor
, 2.5 GHz, 4 MB L3 cache
•
Intel® Core™ i7-3517UE (ULV) dual-core processor, 1.7 GHz, 4 MB L3 cache
• Intel® QM77 Express Chipset
• Up to 16 GB, dual-channel, DDR3 SDRAM memory with ECC running at 1600 MHz on two
SODIMM sockets
• Integrated 3D high-performance processor graphics controller with up to three high-resolu-
tion graphics interfaces (1x VGA and 2 x DP)
• Digital display support for resolutions up to 2560 x 1600 pixels @ 60 Hz
• Analog display support for resolutions up to 2048 x 1536 pixels @ 75 Hz
• Three Gigabit Ethernet interfaces based on three Intel® 82574L controllers:
• Two interfaces switchable between front I/O and rear I/O (with Wake-on-LAN support)
• One interface available on the CP3003-HDD extension module (8HP)
• Six SATA interfaces with SATA RAID 0/1/5/10 support:
• One SATA 6 Gb/s interface for one external, standard HDD/SSD
• One SATA 3 Gb/s interface for up to 32 GB SLC NAND flash memory via an optional
SATA Flash module
• One SATA 3 Gb/s interface for one CFast memory card (8 HP with CP3003-HDD/
CP3003-XMC) or one SATA 2.5" HDD/SSD (12 HP)
• One SATA 6 Gb/s interface for one SATA 2.5" HDD/SSD (8 HP with CP3003-HDD)
• Two SATA 3 Gb/s interfaces for rear I/O
• Five USB ports:
• Two USB 2.0 ports on front I/O
• Two USB 2.0 ports on rear I/O
• One USB 3.0 port on the 120-pin onboard high-speed I/O extension connector
• Two DisplayPort interfaces available on the CP3003-HDD extension module
• One x8 PCI Express 2.0 XMC interface available on the CP3003-XMC ex. module
• 32-bit/ 33 MHz PCI/PCI-X hot swap CompactPCI interface (PICMG 2.0); 66 MHz on request
• Compatible with CompactPCI Specification PICMG 2.0 Rev. 3.0 and usable in the system
controller slot as well as in a peripheral slot (the PCI interface is isolated in peripheral slot)
• TCG 1.2-compliant Trusted Platform Module (TPM)
• Two SPI boot flashes for two separate uEFI BIOS images:
• One standard SPI boot flash
• One recovery SPI boot flash
• Watchdog timer
• Battery-backed real-time clock (RTC)
• One onboard DIP switch for board configuration
•Two COM ports:
• COMA (RS-232) either on the 8 HP extension module or on the rear I/O
• COMB (RS-232) on the rear I/O
• Peripheral extension connectors:
• 120-pin high-speed I/O extension connector for 8 HP extension
• 60-pin high-speed PCI Express extension connector for 8 HP extension
• SPI extension connector
• Rear I/O on the CompactPCI connector J2
• 4 HP or 8 HP, 3U CompactPCI (12 HP on request)
• Several rear I/O configurations
• Power-up sequencing and in-rush current optimized design
• Passive heat sink solution for forced airflow cooling
• AMI Aptio®, a uEFI-compliant platform firmware
To Next Page
