Krone Big Pack 1270 - Page 447

Contents
Supplement to Operating Instructions 150000773_00_en
BiG Pack 1270, BiG Pack 1270 XC, BiG Pack 1290, BiG Pack 1290 HDP, BiG Pack 1290 HDP XC, BiG
Pack 1290 XC, BiG Pack 890, BiG Pack 890 XC
3
8.6 Calling up road travel screen ..................................................................................................... 38
8.7 Changing to automatic mode..................................................................................................... 38
8.8 Changing to manual mode......................................................................................................... 38
8.9 Switching the warning beacon on/off ......................................................................................... 39
8.10 Selecting other functions ........................................................................................................... 39
8.11 Switching the working light on/off .............................................................................................. 39
8.12 Releasing/locking self-steering axle .......................................................................................... 40
8.13 Switching the starting aid on/off ................................................................................................. 40
8.14 Opening/closing bale channel flaps ........................................................................................... 41
8.15 Lower the bale chute ................................................................................................................. 41
8.16 Automatic bale ejection.............................................................................................................. 41
8.17 Selecting "Counter/Detail counter" menu................................................................................... 41
8.18 Selecting a menu Level ............................................................................................................. 41
8.19 Reset bale length to zero ........................................................................................................... 41
8.20 Trigger knotter............................................................................................................................ 42
8.21 Raising/lowering blade cassette ................................................................................................ 42
8.22 Setting the target bale channel flap pressure (manual mode) ................................................... 42
8.23 Setting target baling force (automatic mode) ............................................................................. 43
8.24 Setting target bale length ........................................................................................................... 43
8.25 Setting the target number of MultiBales .................................................................................... 44
8.26 Operating machine via joystick .................................................................................................. 44
8.26.1 Auxiliary functions (AUX) ........................................................................................................... 44
8.26.2 Auxiliary configuration of a joystick............................................................................................ 45
9 Terminal – menus [Medium Plus/Comfort Plus Electronics]............................................... 47
9.1 Menu Structure .......................................................................................................................... 47
9.2 Recurring icons.......................................................................................................................... 48
9.3 Bring up menu level .................................................................................................................. 49
9.4 Selecting menu .......................................................................................................................... 50
9.5 Changing value.......................................................................................................................... 51
9.6 Changing mode ......................................................................................................................... 52
9.7 Menu 1 "Knotter" ....................................................................................................................... 52
9.7.1 Menu 1-1 "Correction value for bale length" .............................................................................. 53
9.7.2 Menu 1-2 "Knotter signal" .......................................................................................................... 53
9.7.3 Menu 1-3 "Knotter monitoring"................................................................................................... 54
9.7.4 Menu 1-4 "Blow interval"............................................................................................................ 55
9.7.5 Menu 1-5 "Blowing time"............................................................................................................ 55
9.7.6 Menu 1-9 "Calibrate MultiBale".................................................................................................. 56
9.8 Menu 2 "Sensitivity of direction display" .................................................................................... 57
9.9 Menu 3 "Central lubrication" ...................................................................................................... 58
9.10 Menu 4 "Bale scales" ................................................................................................................. 59
9.11 Menu 5 "Moisture measurement"............................................................................................... 60
9.11.1 Menu 5-1 "Alarm message for moisture measurement" ............................................................ 61
9.11.2 Menu 5-2 "Correction value for moisture measurement" ........................................................... 61
9.12 Menu 6 "Silage additive system"................................................................................................ 63
9.13 Menu 13 "Counters"................................................................................................................... 63
9.13.1 Menu 13-1 "Customer counter".................................................................................................. 64
9.13.2 Menu 13-2 "Total counter" ......................................................................................................... 67
9.14 Menu 14 "ISOBUS".................................................................................................................... 69
9.14.1 Menu 14-1 “Diagnostics Auxiliary (AUX)” .................................................................................. 69
9.14.2 Menu 14-2 “Driving Speed Display Diagnostics/Direction Display Diagnostics”........................ 70
9.14.3 Menu 14-3 "Configuring main window" ...................................................................................... 71
9.14.4 Menu 14-4 "Set background colour" .......................................................................................... 72
9.14.5 Menu 14-9 “Switching Between the Terminals” ......................................................................... 73
9.15 Menu 15 "Settings" .................................................................................................................... 74
9.15.1 Menu 15-1 “Sensor Test”........................................................................................................... 74
9.15.1.1 Checking/adjusting sensor B22 "Bale on chute"........................................................................ 79
9.15.2 Menu 15-2 "Actuator test" .......................................................................................................... 81
9.15.3 Menu 15-3 "Software info" ......................................................................................................... 83
9.15.4 Menu 15-4 "Error list"................................................................................................................. 83
9.16 Alarm messages ........................................................................................................................ 84
9.16.1 Error Messages.......................................................................................................................... 84