LEMKEN Juwel 8 - Working Tools

To Next Page

To Previous Page

Layout and description

5.2.7 Working tools

The following working tools are available as accessories:

Trash board (1)

Skimmer (2)

Coulter (3)

Main Page

Table of Contents5
General Information11
Liability11
Guarantee11
Copyright12
Optional Accessories12
Symbols Used in the Operating Instructions13
Hazard Classes13
Information13
Environmental Protection13
Indication of Passages14
Safety Measures and Precautions15
Target Group15
Intended Use15
Safety Features of the Device16
Safety and Warning Signs16
General Information16
Position of Warning Symbols16
Meaning of Warning Signs17
Meaning of Other Symbols18
Special Safety Instructions19
Danger Areas During Implement Operation21
Residual Risks21
Hazard Caused by Mechanical Systems22
Hazard Caused by Hydraulic Systems22
Applicable Rules and Regulations22
Operation on Public Highways22
Lighting System and Identification22
Requirements of the Tractor23
Axle Loads24
Check before Departure28
Correct Behaviour in Road Traffic29
Obligation of the Operator29
Safe Use of the Implement30
General30
Personnel Selection and Qualifications31
Hydraulic System32
Handing over the Implement33
Layout and Description34
Overview34
Description34
Headstock34
Turnover Device34
Optiquick Adjustment System35
Basic Frame35
Depth Wheel35
Plough Body36
Working Tools37
Disc Coulters38
Lighting System38
Preparations on Tractor39
Tyres39
Lifting Rods39
Top Link39
Chains and Stabilisers of the Three-Way Linkage39
Hydraulics39
Hydraulic Equipment Required40
Installing the Button41
Preparing the Implement42
Removing the Lighting Equipment42
General42
With Uniwheel42
With Depth Control Wheel43
Upper Control Link Length43
Support Wheel or Depth and Transport Wheel44
Skimmer44
Three-Point Connection45
Attaching the Implement46
Specific Safety Information46
General46
Uncoupling the Implement48
General48
Driving on Public Roads50
Laws and Regulations50
Warning Boards and Lighting50
Transport Speed50
Installing the Lighting Equipment51
With Uniwheel51
With Depth Control Wheel52
Subsoilers53
Operation54
Specific Safety Information54
Turning the Plough Frame55
Angle56
General Information56
Operating the Hydraulic Inclination Adjustment System56
Setting the Front Furrow Width57
General Information57
Front Furrow Width, Mechanical57
Front Furrow Width, Mechanical, in Conjunction with Hydraulic Frame Swivelling58
Front Furrow Width, Hydraulic60
Tractor/Plough Pull Line61
Working Depth61
Hydraulic Frame Swivelling62
Duramaxx Plough Body63
Pitch Angle63
DURAL Plough Body64
Contact Angle64
Tail Pieces65
Working Width for each Base66
Juwel V66
Juwel67
Landside68
Skimmers69
General Information69
Adjustment of the Projection Angle69
Working Depth70
Moving Forwards or Backwards70
Trashboard71
Duramaxx71
Sword Coulter72
Disc Coulters72
General72
Working Depth73
Lateral Distance74
Swivel Action Limiter75
Subsoiler75
Depth Control Wheel and Depth and Transport Wheel76
General Instructions76
Moving the Hydraulic Uni Wheel from the Working Position to the Transport Position7476
Moving the Hydraulic Uni Wheel from the Transport Position to the Working Position7779
Moving the Hydraulically Dampened Uni Wheel from the Working Position to the Transport Position80
Moving the Hydraulically Dampened Uni Wheel from the Transport Position to the Working Position82
Working Depth Adjustment83
On-Land Version (OF)87
General87
Converting from F Operation to O Operation88
Converting from O Operation to F Operation89
Adjustment Centre90
Overload Protection92
Shearing Protection92
Hydromatic Hydraulic Overload Protection93
General93
Setting the Release Force94
Operation96
Releasing the Pressure in the Hydraulic System96
Attachment Arm97
Put the Implement out of Operation98
Shutting down the Implement in an Emergency98
Disposal98
Maintenance and Repairs99
Special Safety Instructions99
General99
Working under the Raised Device99
Immobilise the Implement for Maintenance and Repairs100
Working on the Hydraulics100
Personnel Qualifications100
Protective Equipment101
Utilised Tool101
Environmental Protection102
Maintenance Intervals102
After the Initial Start-Up (at the Latest after 2 Hours)102
Daily Inspection102
Weekly Inspection103
Tightening Torques103
General Information103
Bolts and Nuts Made of Steel104
Wheel Bolts and Wheel Nuts104
Air Pressure of the Tyres105
Check the Connections to the Tractor106
Hydraulic Connections106
Electrical Connections106
Lubrication Chart107
Troubleshooting108
Hydraulic Equipment - Turncontrol108
Fault Messages - Turncontrol108
Plough Intake and Depth Control, Slippage109
Miscellaneous109
Transport on Public Roads110
Laws and Regulations110
Warning Boards and Lighting Equipment110
Transport Speed110
Technical Data111
Model Overview111
Permitted Output Range111
Weight112
Type Plate112
Index114

LEMKEN Juwel 8 - Working Tools

Table of Contents

Related product manuals