What to do if the Mitutoyo CONTRACER CV-2100 analysis software does not start up properly?
If the analysis software isn't starting, first ensure the measuring unit is powered on by pressing the power switch. Then, check the cable connections and correct them if necessary.
What to do if power is not supplied when the power switch is turned on for Mitutoyo CONTRACER CV-2100?
If power isn't supplied when you turn on the power switch: * Make sure the AC adapter cable is securely connected. * Test the receptacle with another electrical appliance to verify it's providing power. * Ensure you are using the AC adapter that was supplied with the unit.
Why is the hold mode not activated on my Mitutoyo CONTRACER CV-2100 Measuring Instruments, even after pressing the hold switch?
The hold mode may not activate if the stylus is indented over the measuring range. Retract the stylus using the up/down fine feed knob.
What to do if Mitutoyo CONTRACER CV-2100 machine moved abruptly?
If the machine moved abruptly, it could indicate a break in the wiring inside the cabinet or elsewhere. Contact your dealer or the nearest Mitutoyo sales office/service center.
General| Brand | Mitutoyo |
|---|---|
| Model | CONTRACER CV-2100 |
| Category | Measuring Instruments |
| Language | English |
Explains the meaning of safety symbols like DANGER, WARNING, and CAUTION.
Defines the different types of notes (IMPORTANT, NOTE, TIP) used to convey information.
Specifies the intended use of the product for measuring specific workpieces.
Lists hazardous actions to avoid, such as modification, unstable installation, or contact with water.
Illustrates the recommended work zone and danger zone around the product.
Details risks associated with electrical shock and precautions for safe operation.
Highlights risks from moving parts, sharp edges, and potential pinch points.
Addresses risks related to workpiece movement, securing, and potential falls.
Information regarding compliance with export control regulations for the product.
Instructions for disposing of products outside of European countries.
Guidance on disposing of WEEE-compliant equipment in European countries.
Defines the scope of the manual, focusing on system configuration and setup.
Provides a general introduction to the stylus type contour measuring instrument.
Lists the product code numbers for the CV-2100 series.
Illustrates the components and connections of the CV-2100 series system.
Identifies and describes the functions of the main unit and stand components.
Specifies requirements for temperature, humidity, and vibration for optimal installation.
Provides diagrams showing the required floor space for system installation.
Details the procedure for mounting the measuring main unit onto the stand.
Explains how to connect the AC adapter and USB cables.
Describes the steps required to detach the measuring main unit from the stand.
Provides instructions for mounting the auxiliary weight assembly.
Advises against self-relocation and recommends contacting service.
Ensures that all connecting cables are properly attached as specified.
Guides on how to correctly remove and install a stylus onto the arm.
Details the procedure for attaching an arm to the main arm.
Outlines the steps to power on the printer, PC, and measuring main unit.
Explains the process of detecting Z1-axis zero-position and setting X-axis origin.
Describes how to set arm and stylus types to prevent measurement errors.
Details methods for moving the stylus using the drive knob or software.
Provides steps to adjust the measuring force using a standard accessory gage.
Covers essential calibrations like Z-axis gain, symmetry, and stylus radius.
Walks through setting up a workpiece and starting a basic measurement.
Provides the procedure to safely shut down the analysis software and system.
Instructions for cleaning the exterior of the unit with appropriate materials.
Details periodic grease application requirements for moving parts.
Identifies consumable parts like motors and wires and their replacement recommendations.
A guide to common symptoms, their check points, and suggested remedies.
Lists error codes displayed on the level meter and their corresponding remedies.
Provides detailed technical specifications for CV-2100N4 and CV-2100M4 models.
Illustrates the external dimensions of the CV-2100N4 and CV-2100M4 units.
Lists the standard accessories included with the CV-2100N4 and CV-2100M4.
Details the range of optional accessories available for the CV-2100 series.
Includes information on auxiliary weights and their usage with arms and styli.
To Next Page