NEC SL2100 - Page 102

Program
No.
Program Name Input Data Default
44-05-02 ARS/F-Route Table - Delete Digits 0 ~ 255
(255 = Delete All)
0
44-05-03 ARS/F-Route Table - Additional Dial Number Ta-
ble
0 ~ 100 0
44-05-04 ARS/F-Route Table - Beep Tone 0 = Off
1 = On
0
44-05-05 ARS/F-Route Table - Gain Table Number for In-
ternal Calls
0 ~ 100
0 = No Setting
0
44-05-06 ARS/F-Route Table - Gain Table Number for Tan-
dem Connections
0 ~ 100
0 = No Setting
0
44-05-11 ARS/F-Route Table - Network Specified Parame-
ter Table
0 ~ 16 0
44-06-01 Additional Dial Table - Additional Dial Up to 36 digits
Enter : 1 ~ 9, 0,
*
, #, Pause
(press LK 1 to enter a pause)
No Setting
44-07-01 Gain Table for ARS/F-Route Access - Incoming
Transmit
1 ~ 63
(- 15.5 dB ~ + 15.5 dB)
32 (0 dB)
44-07-02 Gain Table for ARS/F-Route Access - Incoming
Receive
1 ~ 63
(- 15.5 dB ~ + 15.5 dB)
32 (0 dB)
44-07-03 Gain Table for ARS/F-Route Access - Outgoing
Transmit
1 ~ 63
(- 15.5 dB ~ + 15.5 dB)
32 (0 dB)
44-07-04 Gain Table for ARS/F-Route Access - Outgoing
Receive
1 ~ 63
(- 15.5 dB ~ + 15.5 dB)
32 (0 dB)
80-03-01 DTMF Tone Receiver Setup - Detect Level 0 = 0 dBm ~ - 25 dBm
1 = - 5 dBm ~ - 30 dBm
2 = - 10 dBm ~ - 35 dBm
3 = - 15 dBm ~ - 40 dBm
4 = - 20 dBm ~ - 45 dBm
5 = - 25 dBm ~ - 50 dBm
6 = - 30 dBm ~ - 55 dBm
Refer to the Program-
ming Manual for the
default values.
80-03-02 DTMF Tone Receiver Setup - Start Delay Time 0 ~ 255 (0.25 ms ~ 64 ms) Refer to the Program-
ming Manual for the
default values.
80-03-03 DTMF Tone Receiver Setup - Min. Detect Level 0 ~ 15
DTMF Tone 0 = - 10 dBm (0) to -
25 dBm (15)
DTMF Tone 1 = - 15 dBm (0) to -
30 dBm (15)
DTMF Tone 2 = - 20 dBm (0) to -
35 dBm (15)
DTMF Tone 3 = - 25 dBm (0) to -
40 dBm (15)
DTMF Tone 4 = - 30 dBm (0) to -
45 dBm (15)
DTMF Tone 5 = - 35 dBm (0) to -
50 dBm (15)
DTMF Tone 6 = - 40 dBm (0) to -
55 dBm (15)
Refer to the Program-
ming Manual for the
default values.
SL2100 ISSUE 1.0
1-88
Automatic Route Selection (ARS/F-Route)
A