EQ / EFX
7.2
MIC ECHO
EchoPRESET:¥Stereo Echo 03
→EchoTIME:127 FEEDBACK:052
SYNCtoMIDI: DISABLED
EchoSEND:074
ECHO TIME= 446 ms
MIC ECHO
→EchoPRESET: Stereo Echo 03
EchoTIME:070 FEEDBACK:052
SYNCtoMIDI: DISABLED
EchoSEND:074
SELECT ECHO PRESET
MIC ECHO
EchoPRESET: Stereo Echo 03
SYNCto:1/2 FEEDBACK:052
→SYNCtoMIDI: ENABLED
EchoSEND:074
SELECT SYNC MODE
MIC ECHO
EchoPRESET: Stereo Echo 03
→SYNCto:1/4 FEEDBACK:052
SYNCtoMIDI: ENABLED
EchoSEND:074
ECHO TIME= 316 ms
Mic Echo
The Echo dedicated to the microphone allows to add various types of echo effects to your voice. The repetitions
can be synchronized with the rhythm of the backing tracks.
EchoPRESET
Enabled Preset.
8 Presets are available in the default configuration.
N.B.: By means of the PC software supplied, you can prepare your own
Presets and add them to the Preset library saved on the Compact Flash card.
¥ When the name of the Preset is preceded by a graphic
symbol, this shows that the Preset has been modified.
N.B.: changes that are not saved produce temporary effects, useful for
example for carrying out impromptu changes required during live
performances: When a new Preset is uploaded (including the same
recently edited Preset), it will have the values with which it was saved
before editing work just carried out.
EchoTIME
Delay time.
Using this control, you can change the delay time of the
effect’s main echo.
In fact, you can make the Echo longer or shorter according
to your needs.
The MIDI value 1..127 is shown in milliseconds at the bottom of the page.
FEEDBACK
Delay feedback.
Using this control, you can set the amount of signal to feed back to the processor.
In other words, you can change the effect’s persistence.
The MIDI value 1..127 is shown as a percentage at the bottom of the page.
SYNCtoMIDI
Echo synchronization mode.
This control allows to choose whether or not to synchronize the Echo’s repetitions with the tempo of the song
being performed. In other words, it allows to have an Echo able to “keep time” with any backing track.
The setting of this control considerably changes the behaviour of the effect and also causes a change of the
name and function of one of the other parameters:
DISABLED =The values of the repetitions are set by the
EchoTIME control.
The repetitions of the Echo operate with fixed
values, no matter what the tempo of the songs.
ENABLED =The repetitions are synchronized with the
tempo of the song being performed.
The repetitions of the Echo follow the effective
performance tempo of each song.
The EchoTIME parameter is replaced by the
SYNCto control.
SYNCto
Synchronization value.
Allows to choose the value of the music note to which the Echo’s
repetitions are to be synchronized: 1/2, 1/4, 1/8, 1/16, 1/32.
The corresponding time value is shown in milliseconds at
the bottom of the page. Obviously, due to the dynamic
nature of the SYNCtoMIDI function, this value varies along
with the speed of the songs (e.g. in STOP = 0 ms).
The note values and corresponding milliseconds are subject
to some automatic optimisation, to avoid synchronization times that are unsuitable from a musical point of view.
EchoSEND
The microphone signal sent to the Echo effect.
Adjusts the amount of microphone signal sent to the effect.
N.B.: the SEND control is the exact equivalent of an effect send on a normal audio mixer and must not be confused with the volume of the
effects, which on the other hand is adjusted with the MIC EFX pot on the right-hand side of the OkyWeb2.
In other words, the SEND parameter controls how much signal enters the effect and the MIC EFX pot how much is fed out.
To Next Page
Loading...