PTW MP3-PL - Figure 7: Assembling SCANLIFT, Positioning Device, Chamber Cable Holding Device and Perspex Tank

58 pages

Save Page as PDF

To Next Page

To Previous Page

MP3-PL Therapy Beam Analyzer T41050

Operating Manual – Assembly of the System

D850.131.05/01 en

Figure 7: Assembling SCANLIFT, positioning device, chamber cable holding device and Perspex tank

Main Page

General Information2
Table of Contents4
Contents4
Illustrations6
Intended Use7
Safety Information8
Figure 1: Definition of Patient Environment13
Operating Manual15
The Components of the MP3-PL System15
Figure 2: MP3-PL System with Accessories for Measurements with 24 Pinpoint Chambers15
Figure 3: MP3-PL System with Accessories for Measurements with a Measuring and a Reference Detector16
Perspex Tank17
Figure 4: MP3-PL Perspex Tank with Junction Box and Moving Mechanism (Top: Front View; Below: Rear View)17
Moving Mechanism18
Figure 5: Connections at the Junction Box18
Positioning Device19
Figure 6: Positioning Device for Tank Alignment19
SCANLIFT Carriage and Reservoir20
Control Unit and Control pendant20
Assembly of the System21
Assembling SCANLIFT, Positioning Device, Chamber Cable Holding Device and Perspex Tank21
Figure 7: Assembling SCANLIFT, Positioning Device, Chamber Cable Holding Device and Perspex Tank22
Assembling the Junction Box and the Moving Mechanism23
Figure 8: Mounting the A-Axis24
Figure 9: Mounting the B-Axis25
Figure 10: Mounting the C-Axis26
Installation of the System for Measurement27
Quickstart (Workflow)27
Mounting Detectors on the Moving Mechanism28
Figure 11: Inserting the 24 Pinpoint Chambers into the 3D-Detectorblock28
Figure 12: Vertical Mounting of the 3D-Detectorblock with 24 Pinpoint Chambers29
Figure 13: Horizontal Mounting of the 3D-Detectorblock with 24 Pinpoint Chambers29
Figure 14: Inserting the 24 Pinpoint Chambers into the Linear Detector Holder30
Figure 15: Vertical Mounting of the Linear Detector Holder with 24 Pinpoint Chambers31
Figure 16: Horizontal Mounting of the Linear Detector Holder with 24 Pinpoint Chambers32
Figure 17: Horizontal Mounting of the Bragg Peak Chamber33
Figure 18: Vertical Mounting of the Bragg Peak Chamber34
Connecting the Detectors35
Figure 19: Laying and Bundling of the Chamber Cables35
Figure 20: Chamber Cable Holding Device T20015.1.20036
Mounting and Connecting the Reference Detector37
Figure 21: Mounting the Reference Detector37
Figure 22: Mounting the Reference Detector Holder38
Mounting the Inhomogeneous Phantom T4303139
Mounting the Hemisphere T41029.3.23139
Figure 23: Mounting the Inhomogeneous Phantom T4303139
Figure 24: Mounting the Hemisphere T41029.3.23139
Mounting the Wedge T41029.1.22040
Mounting the Film Holding Device T4004040
Figure 25: Mounting the Wedge T41029.1.22040
Figure 26: Mounting the Film Holding Device T4004040
Connecting SCANLIFT41
Figure 27: Coupling of the Plastic Hose of the Water Reservoir41
Filling with Water42
Connecting the Control Unit and Control pendant44
Installation Check45
Error Messages and Troubleshooting46
Technical Manual47
Technical Specifications47
Order Information49
Service Manual51
Cleaning51
Preventive Maintenance53
Storage54
Disposal of the Product54
Literature55
Appendix: China Electronic Industry Standard Compliance56
Index58

PTW MP3-PL - Figure 7: Assembling SCANLIFT, Positioning Device, Chamber Cable Holding Device and Perspex Tank

Table of Contents

Related product manuals