Rockwell Automation Allen-Bradley PowerMonitor 5000 Unit - Page 92

514 pages

To Next Page

To Previous Page

92 Rockwell Automation Publication 1426-UM001J-EN-P - August 2019

Chapter 4 Metering

Command.System_Registers

• Clear all energy registers

• Set status input count

• Force relay or KYZ output on, off, or clear force

• Restore factory defaults

• Reset power monitor

Setup

No setup is needed.

Main Page

Default Chapter3
- Table of Contents3
- About this Manual7
- Intended Audience7
- Summary of Changes7
- Additional Resources8
- Catalog Number Explanation8
Chapter 19
- Product Description9
- Safety9
- Powermonitor 5000 Unit Features and Functions10
- Before You Begin14
- Product Disposal14
- Mounting Considerations15
Chapter 218
- Wire the Powermonitor 5000 Unit18
- Connect Communication31
Setup Using the Web Interface49
Chapter 358
- Commands58
- Setup Using Custom Add-On Profile59
- Setup Using Communication69
- Setup Using Optional Software69
Chapter 4 Basic Metering71
- Wiring Diagnostics73
- Wiring Correction78
- Metering Overview80
- Energy Metering81
- Demand Metering83
- Power Metering87
- Voltage, Current, Frequency Metering89
- Configuration Lock91
Chapter 594
Chapter 595
Harmonic Analysis96
- Sag and Swell Detection102
- Waveform Recording (M6 and M8 Model)104
Chapter 6 Logging Overview112
- Waveform Log (M6 and M8 Model)118
- Energy Log134
- Data Log138
- Min/Max Log148
- Load Factor Log155
- Time-Of-Use (TOU) Log156
- Event Log159
- Setpoint Log163
- Alarm Log165
- Power Quality Log (M6 and M8 Model)171
- Trigger Data Log (M6 and M8 Model)176
- Snapshot Log179
- EN 50160 Weekly and Yearly Logs181
Chapter 7 Relay and KYZ Outputs183
- Status Inputs187
- Setpoints191
Chapter 8 Security209
- Date and Time Functions211
- Network Time Synchronization213
- System Error Response217
- Miscellaneous Commands218
Chapter 9 Native Ethernet Communication219
- Optional Controlnet Communication221
- Optional Devicenet Communication221
- Electronic Data Sheet (EDS)222
- Powermonitor 5000 Unit Memory Organization223
- Communication Command Summary224
- Ethernet/Ip Object Model226
- Devicenet and Controlnet Object Model227
- Explicit Messaging227
- Examples: Explicit Message Setup228
- SCADA Applications235
- Controller Applications: Class 1 Connection242
- CIP Energy Object260
Chapter 10265
Update the Powermonitor 5000 Unit Firmware265
- Rockwell Automation Publication 1426-UM001J-EN-P - August266
- Upgrading the Powermonitor 5000 Model and Communication267
- Use the Controlflash Utility to Update Firmware267
- Summary of Data Tables269
Appendix A272
- Data Tables272
- Information Tables429
Appendix B432
Appendix B433
Certifications434
Appendix C Terminal Setup437
- Introduction437
Appendix D Terminal Setup447
- Introduction447
- Compression Algorithm455
IEEE 519 Pass/Fail Capability (M6 and M8 Models)459
Appendix E460
Appendix F460
- IEEE 519 Pass/Fail Results460
- IEEE 519 Short-Term and Long-Term Harmonic Results461
Appendix G463
- Ieee 1159-2009463
- Power Quality Event Classification Per463
- Transients (Category 1.1.3, 1.2.1)(M8 Model)464
- Interruptions) (M6 and M8 Model)465
- Short Duration RMS Variations465
- Long Duration RMS Variations466
- Voltage and Current Imbalance (Category 4.0)467
- Waveform Distortion468
- Flicker (Voltage Fluctuations, Category 6.0)469
- Power Frequency Variations (Category 7.0)470
Introduction473
Appendix H474
- Operation474
- Results478
- Introduction483
Appendix I Power Quality Parameters484
- Introduction493
Appendix J496
- Install the AOP496
Glossary499
Index507
- Rockwell Automation Publication 1426-UM001J-EN-P - August508

Rockwell Automation Allen-Bradley PowerMonitor 5000 Unit - Page 92

Table of Contents

Related product manuals