SCHIEBEL AB Series - Technical Data; Binary Inputs Technical Data; Binary Outputs Technical Data; Analogue Inputs Technical Data

19 Technical data
Operating instructions for actuators type AB with SMARTCON control unit
OM-ENGLISH-CSC-V2.08-2019.11.07
19 Technical data
19.1 Binary inputs
Count: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Nominal voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24VDC
towards common ground
Thresholf voltage for input set: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>12V
Treshold voltage for input not set: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<5V
Maximum voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30VDC
Current consumtion at 24 V: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . typ. 5mA
Binary inputs are separated from other controllers via optocouplers.
Figure 80
19.2 Binary outputs
Count: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24VDC +/- 6V
(either from internal or external)
Max voltage drop at set output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2V
output voltage at non-set output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <1V
Maximum current per output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA (short circuit proof)
Maximum permissible total current for all outputs: . . . . . . . . . . . . . . .150mA for internal power supply
Maximum permissible total current for all outputs: . . . . . . . . . . . . . . .250mA with external supply
Fuse: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375mA time-lag
(Littelfuse 454 NANO
2
Slo-Blo
R

)
Binary outputs with external supply are separated from other controllers via optocouplers.
19.3 Analogue inputs
Count: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Current range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-20,5mA
Resolution: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Bit
Accuracy: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,5%
Input resistance: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Ohm
Reference ground is the common ground of the controller and the auxiliary voltage (see section 19.5).
19.4 Analogue outputs
Count: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
54