How to troubleshoot no display, pulse frequency, or active status signal on SICK FLOWSIC600 Measuring Instruments?
If the SICK Measuring Instruments show no display, pulse frequency, or active status signal, it might be due to a faulty power supply. Check the input voltage at terminals 1 and 2, and inspect the cables and terminal connections, taking necessary safety precautions. If the issue persists, the device may be defective.
What causes different speed of sound in the individual paths in SICK Measuring Instruments?
The different speed of sound in the individual paths in SICK Measuring Instruments is caused by a faulty transducer or electronic module.
Why is there an implausible speed of sound in my SICK Measuring Instruments?
The implausible speed of sound in SICK Measuring Instruments indicates that the gas composition, pressure, or temperature measurement is incorrect. Therefore, check gas composition, pressure, and temperature.
What does the yellow light for any Data-Log "full" mean on SICK FLOWSIC600?
The yellow light for any Data-Log "full" on SICK Measuring Instruments means that the DataLog in question is configured to "blocking" and is full of entries. Check the DataLog whether the DataLog is to be configured as "rolling".
What does the red light for any Logbook "full" mean on SICK FLOWSIC600?
The red light for any Logbook "full" on SICK Measuring Instruments means that the logbook in question is configured to "blocking" and is full of entries. Download and check all logbook entries. Clear the meter logbook. Consider reconfiguring the logbook to "rolling".
What does the yellow light "Logbook contains unack. entries" mean for SICK Measuring Instruments?
The yellow light "Logbook contains unack. entries" on SICK Measuring Instruments indicates that the logbook contains unacknowledged entries. Download and check all logbook entries.
What does the yellow light "Check request" indicate on SICK Measuring Instruments?
The yellow light "Check request" on SICK Measuring Instruments means that one or more paths have failed, or another problem affects the measurement accuracy.
What does the red light "Path failure" mean on SICK FLOWSIC600?
The red light "Path failure" on SICK Measuring Instruments indicates that one or more paths have failed.
Why is the yellow light "User Warning Limit exceeded" on my SICK Measuring Instruments?
The yellow light "User Warning Limit exceeded" on SICK Measuring Instruments indicates that a User Warning Limit was exceeded. You should check the User Warnings.
What to do if the red light "Measurement valid" is on for SICK Measuring Instruments?
If the red light "Measurement valid" is on, it indicates that the measurement is invalid or the meter is in Configuration Mode. If the meter is in Configuration Mode, switch it to Operation Mode by choosing "File / Operation Mode" from the menu.
Information on product identity, manufacturer, and contact details.
Lists of registered trademarks and the guarantee statement for product characteristics.
Definitions of acronyms and technical terms used throughout the manual.
Explanation of symbols indicating hazards like general danger, voltage, and explosive atmospheres.
Defines signal words (DANGER, WARNING, CAUTION, NOTICE) and their severity.
Explanation of symbols for information, technical data, and links.
Provides an overview of the manual's scope, content, and related documentation.
Outlines critical safety guidelines, intended use, and authorized personnel requirements.
Covers dangers from gases, pressure, loads, and general safety measures.
Details on environmental impact and proper disposal procedures for the instrument.
Describes the main hardware components: meter body, transducers, and SPU.
Explains operating modes, meter states, and signal behaviors.
Details the MEPAFLOW600 CBM software features and installation.
General considerations, delivery check, and transport/storage guidelines.
Guidelines for measuring location and pipeline installation configurations.
Steps for mounting the meter, selecting parts, and aligning components.
Instructions for general information, cable specifications, and connections.
General commissioning steps, PC/laptop connection via RS485/RS232/USB.
Steps for connecting and starting the MEPAFLOW600 CBM software.
Guided field setup, function tests, and path compensation activation.
Instructions for sealing the signal processing unit after commissioning.
General information on the low-maintenance nature and routine checks.
Procedures for comparing SOS, checking meter health, and time synchronization.
Generating maintenance reports and downloading optional data like logbooks.
Basic steps for identifying and resolving common measurement problems.
Interpreting meter indications, system alarms, and user warnings.
Solutions for issues related to connecting the meter to the software.
Details on CE certificate, standards, type approvals, and technical specifications.
Classification and overview of event entries in logbooks and the MEPAFLOW600 CBM.
Connection diagrams and wiring examples for hazardous areas (CSA, ATEX).
Diagrams illustrating the correct placement of seals on various meter components.
General| Measurement Principle | Ultrasonic |
|---|---|
| Power Supply | 24 V DC |
| Medium | Gas |
| Temperature Range | -40°C to +70°C |
| Output Signal | 4 to 20 mA, Modbus |
| Measured Variable | Flow velocity |
| Gas Types | Natural gas |
| Response Time | < 1 s |
| Housing Material | Aluminum |
| Certifications | ATEX, IECEx |
| Protection Class | IP66 |
| Repeatability | ±0.5% of reading |
To Next Page
