Siemens SIMATIC ET 200SP - Security Information

6.5.29 SecureDisplay version [secureDisplayVersion]......................................................................70
6.5.30 Smallest zoom factor of SecureDisplay (%) [smallestZoomFactorOfSecureDisplay] ............70
6.6 DR04 Calibration curve check................................................................................................70
6.7 DR05 Tare and zero memory.................................................................................................70
6.8 DR06 Configuration of limits ..................................................................................................71
6.8.1 Reference (limits 1 and 2) [limitReference] ............................................................................71
6.8.2 Limit 3 - empty [emptyLimit] ...................................................................................................71
6.8.3 Switch-on delay limit 3 (empty) (s) [delayTimeForEmptyLimit] ..............................................72
6.9 DR07 Interface parameters....................................................................................................72
6.9.1 Assignment DI.0, DI.1, DI.2, CI [functionDI0 to functionDI2] [functionCI] ..............................72
6.9.2 Filtering DI.0, DI.1, DI.2 and CI ..............................................................................................73
6.9.3 Assignment DQ.0, DQ.1, DQ.2 ..............................................................................................73
6.9.4 Reaction to CPU stop / failure [behaviourOnCPUStopOrFailure] ..........................................73
6.9.5 Monitoring of digital outputs [monitoringOfDQ] ......................................................................74
6.9.6 Reaction of digital outputs to a CPU stop / failure [behaviourOfDQOnCPUStopOrFailure]......74
6.9.7 Behavior of digital outputs on error [behaviourOfDQOnError] ...............................................74
6.9.8 Substitute value for DQ.0 to DQ.3 on error ............................................................................74
6.9.9 Trace rate [traceRate] ............................................................................................................75
6.9.10 Subnet mask, IP address, gateway, device name .................................................................75
6.9.11 Activate Modbus communication [activateModbusConnection1]
[activateModbusConnection2]................................................................................................75
6.9.12 Modbus TCP Unit Identifier, port, SWAP options...................................................................76
6.9.13 Byte/Word swap options [byteSwap16Bit] [byteSwap32Bit] [wordSwap32Bit] ......................76
6.9.14 RS485 protocol ......................................................................................................................76
6.9.15 I/O process values 1 to 4 [ioProcessValue1 to ioProcessValue4] .........................................76
6.9.16 I/O process values 5 to 8 [ioProcessValue5 to ioProcessValue8] .........................................77
6.9.17 Event hardware interrupts 4 to 8 [hardwareInterrupt4 to hardwareInterrupt8] .......................78
6.9.18 Source for weight simulation [simulationSource] ...................................................................78
6.10 DR09 Read out module information.......................................................................................78
6.11 DR10 Load cell parameters ...................................................................................................78
6.11.1 Load cell type [loadCellType] .................................................................................................78
6.11.2 Connection technology [fourSixWireSensor]..........................................................................79
6.11.3 Load cell manufacturer [loadCellManufacturer] and load cell order number
[loadCellOrderNumber] ..........................................................................................................79
6.11.4 No. of mechanical support points [numberOfSupportPoints] .................................................79
6.11.5 Averaged load cell characteristic (mV/V) [averagedCharacteristicValue] ..............................79
6.11.6 Nominal load of one single load cell [nominalLoadOfSingleLoadCell] ...................................79
6.11.7 Power line frequency [powerLineFrequency] .........................................................................80
6.11.8 Using a power line filter [PowerLineFilterActivated] ...............................................................80
6.11.9 External / internal sensor supply [internalExternalAdcSupply]...............................................80
6.11.10 Impedance .............................................................................................................................80
6.12 DR15 Preset tare ...................................................................................................................80
6.13 DR16 Configuration of weight simulation ...............................................................................81
6.13.1 Simulate weight......................................................................................................................81
6.13.2 Simulating dosing...................................................................................................................82
6.13.3 Material flow, delay time and opening/closing time................................................................83
6.14 DR18 Digital output and transition control..............................................................................84
6.14.1 Controlling digital outputs.......................................................................................................84
Table of contents
Technology module TM SIWAREX WP351 HF
Operating Instructions, 01/2020, A5E47521010-AA 5