EasyManuals Logo

Siemens SINUMERIK 840D sl Function Manual

Siemens SINUMERIK 840D sl
2184 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1719 background imageLoading...
Page #1719 background image
Basic logic functions: Feeds (V1)
Function Manual, 11/2006, 6FC5397-0BP10-2BA0
3
Table of contents
1 Brief Description ........................................................................................................................................ 5
2 Detailed description ................................................................................................................................... 9
2.1 Path feedrate F ..............................................................................................................................9
2.1.1 General ..........................................................................................................................................9
2.1.2 Type of feedrate G93, G94, G95 .................................................................................................11
2.1.3 Type of feedrate G96, G961, G962, G97, G971..........................................................................13
2.1.4 Feedrate with G33, G34, G35 (thread cutting) ............................................................................18
2.1.4.1 General ........................................................................................................................................18
2.1.4.2 Programmable run-in and run-out path for G33, G34 and G35...................................................20
2.1.4.3 Linear progressive/degressive thread-lead change with G34 and G35.......................................22
2.1.4.4 Stop for thread cutting..................................................................................................................25
2.1.5 Feedrate for G331/G332, rigid tapping ........................................................................................29
2.1.6 Feedrate for G63, tapping with compensation chuck ..................................................................30
2.2 Feedrate FA for positioning axes.................................................................................................30
2.3 Feedrate control...........................................................................................................................32
2.3.1 General ........................................................................................................................................32
2.3.2 Feedrate disable and feedrate/spindle stop.................................................................................33
2.3.3 Feedrate override on machine control panel ...............................................................................34
2.3.4 Programmable feedrate override .................................................................................................40
2.3.5 Dry run feedrate ...........................................................................................................................41
2.3.6 Multiple feedrate values in one block...........................................................................................43
2.3.7 Fixed feedrate values (840D, 810D)............................................................................................49
2.3.8 Feedrate for chamfer/rounding FRC, FRCM ...............................................................................50
2.3.9 Non-modal feedrate FB................................................................................................................52
2.3.10 Programmable singleaxis dynamic response ..............................................................................53
3 Supplementary conditions ....................................................................................................................... 61
3.1 General boundary conditions.......................................................................................................61
3.2 Supplementary conditions for feedrate programming..................................................................61
4 Examples................................................................................................................................................. 63
4.1 Feedrate programming for chamfer/rounding FRC, FRCM .........................................................63
5 Data lists.................................................................................................................................................. 65
5.1 Machine data................................................................................................................................65
5.1.1 NC-specific machine data ............................................................................................................65
5.1.2 Channelspecific machine data.....................................................................................................66
5.1.3 Axis/Spindle-specific machine data .............................................................................................66
5.2 Setting data..................................................................................................................................67
5.2.1 Channelspecific setting data........................................................................................................67
5.2.2 Axis/spindle-specific setting data.................................................................................................67

Table of Contents

Other manuals for Siemens SINUMERIK 840D sl

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 840D sl and is the answer not in the manual?

Siemens SINUMERIK 840D sl Specifications

General IconGeneral
Control TypeCNC
Number of AxesUp to 31
Max Number of Channels10
InterfacesEthernet, PROFIBUS, PROFINET, USB
Interpolation5-axis interpolation
Operating Temperature0°C to 45°C
Relative HumidityUp to 95% (non-condensing)
DisplayTFT color display, various sizes
Programming LanguagesDIN/ISO
Safety FeaturesSafety Integrated
PLCIntegrated PLC S7-300
Drive InterfaceSINAMICS S120
Data StorageCF card, USB
Operating SystemWindows-based

Related product manuals