Siemens SINUMERIK 840D - Page 375

11.03 7 Configuring example
7.3 Safety Integrated with SPL
© Siemens AG 2003 All Rights Reserved
SINUMERIK 840D/SIMODRIVE 611 digital SINUMERIK Safety Integrated (FBSI) - Edition 11.03
7-375
; ----- Variable Dual Port RAM PLC <-> NCK ----
;
DEFINE QUIT
_PLC AS $A_DBB[4]
PLC I/O DB18 variable Symbolic Absolute Associated bit in axis DB
E76.0 $A_INSEP[1] "SPL".NOT_HALTE DB18.DBX38.0 -
E76.1 $A_INSEP[2] "SPL".TUERZUVER DB18.DBX38.1 -
- $A_INSEP[3] - DB18.DBX38.2 -
E76.3 $A_INSEP[4] "SPL".NOT_QUIT DB18.DBX38.3 -
E76.5 $A_INSEP[5] "SPL".SCHLUESSEL DB18.DBX38.4 -
- $A_INSEP[6] - DB18.DBX38.5 -
- $A_INSEP[7] "SPL".KL_AS12_XZ DB18.DBX38.6 -
- $A_INSEP[8] "SPL".KL_AS12_C DB18.DBX38.7 -
- $A_INSEP[9] - DB18.DBX39.0 -
- $A_INSEP[10] - DB18.DBX39.1 -
- $A_INSEP[11] - DB18.DBX39.2 -
- $A_INSEP[12] - DB18.DBX39.3 -
- $A_INSEP[13] - DB18.DBX39.4 -
- $A_INSEP[14-16] - DB18.DBX39.5-7 -
A48.2 $A_OUTSEP[1] "SPL". NOT_HALT1K DB18.DBX46.0 -
- $A_OUTSEP[2] - DB18.DBX46.1 -
- $A_OUTSEP[3] "SPL". KL_663_XZ DB18.DBX46.2 -
- $A_OUTSEP[4] "SPL". KL_663_C DB18.DBX46.3 -
- $A_OUTSEP[5-8] - DB18.DBX46.4-7 -
- $A_INSIP[1] "SPL".IMP_FREI_XZ DB18.DBX54.0 -
- $A_INSIP[2] "SPL".IMP_FREI_C DB18.DBX54.1 -
- $A_OUTSIP[1] "SPL". STOP_A_ABWS DB18.DBX38.0 DB33.DBX 32.2
- $A_OUTSIP[2] "SPL". STOP_A_ABWA DB18.DBX38.1 DB31/32.DBX 32.2
- $A_OUTSIP[3] "SPL". STOP_C_ABW DB18.DBX38.2 DB31/32/33.DBX 32.3
- $A_OUTSIP[4] "SPL". STOP_D_ABW DB18.DBX38.3 DB31/32/33.DBX 32.4
- $A_OUTSI P[5] "SPL". SBH_ABW DB18.DBX38.4 DB31/32/33.DBX 22.1
- $A_OUTSIP[6] "SPL". SG_BIT_0 DB18.DBX38.5 DB31/32/33.DBX 22.3
- $A_OUTSI P[7] - DB18.DBX38.6 -
- $A_OUTSIP[8] - DB18.DBX38.7 -
- $A_OUTSIP[9] "SPL". STAT_IMP_XZ DB18.DBX39.0 -
- $A_OUTSIP[10] "SPL". STAT_IMP_C DB18.DBX39.1 -
- $A_MARKERSIP[1] - DB18.DBX70.0 -
- $A_MARKERSIP[2] "SPL".NOT_HALT DB18.DBX70.1 -
- $A_MARKERSIP[3] - DB18.DBX70.2 -
- $A_MARKERSIP[4] - DB18.DBX70.3 -
- $A_MARKERSIP[5] "SPL".QUIT_MARKER DB18.DBX70.4 -
- $A_MARKERSIP[6] - DB18.DBX70.5 -
- $A_MARKERSIP[7] "SPL".STOP_A_A DB18.DBX70.6 -
- $A_MARKERSIP[8] "SPL".STOP_A_S DB18.DBX70.7 -
PLC I/O PLC variable Symbolic Comment
T20 TIMER1 STOP c-> STOP A (axes)
T21 TIMER2 STOP c-> STOP A (spindle)
T22 T_K_ABFALL Drop-out time of contactors K1, K2
T23 T_VERZUG_1 EMERGENCY STOP on delay time
T24 T_VERZUG_" Acknowledgement delay time
- T30 Teststop_Zeit1 Monitoring duration 2h 40min
- T31 Teststop_Zeit2 Monitoring duration 5h 20min
- T32 Teststop_Zeit3 Monitoring duration 8h
Variable declaration
PLC