To Next PageTo Next PageWhat to do if the Siemens SITRANS P Transmitter display is empty and there are no transmission pulses?
If the Siemens Transmitter display is empty and there are no transmission pulses, the cause may be no or incorrect supply voltage. Check the voltage at the terminals, the connections, and the wiring.
Why does my Siemens Transmitter display "#####" instead of the current measured value?
If the Siemens Transmitter displays "#####" instead of the current measured value, it means that the value is too large to appear on the display. Adjust the unit so that a lower value can be displayed, for example, by selecting bars instead of millibars.
What does INVALID CFG LOOPT mean on my Siemens SITRANS P?
INVALID CFG LOOPT on your Siemens Transmitter indicates that the loop current is fixed because loop test or multidrop mode are enabled. To return to normal operation, disable the loop test or multidrop mode.
How to fix INVALID CFG SIMUL error on a Siemens SITRANS P?
The INVALID CFG SIMUL error on a Siemens Transmitter means the device is in simulation mode, and the pressure measured value is simulated. To return to normal operation, disable simulation.
What causes the INVALID CFG TRNFK error on Siemens Transmitter?
The INVALID CFG TRNFK error on your Siemens Transmitter indicates that wrong characteristic curves are selected. Select one of the following characteristic curves: Linear, proportional to pressure (PRESS); Linear, proportional to level (LEVEL); or Proportional to flow rate, two-step linear up to the application point (VSLN2 or MSLN2).
What does INVALID CFG STSIM mean on Siemens Transmitter and how do I resolve it?
INVALID CFG STSIM on a Siemens Transmitter signifies that the device is in simulation mode and diagnostics are being simulated. Disable simulation to return to normal operation.
How to resolve INVALID CFG ACCES error on a Siemens SITRANS P Transmitter?
The INVALID CFG ACCES error on your Siemens Transmitter means that write protection via user PIN is disabled. Activate write protection via the user PIN by enabling it.
What to do if Siemens SITRANS P shows INVALID CFG PARAM?
If your Siemens Transmitter shows INVALID CFG PARAM, it indicates that the factory settings for Functional Safety are faulty. Replace the device.
General| Housing Material | Stainless steel, aluminum |
|---|---|
| Output Signal | 4 to 20 mA, HART |
| Communication Protocol | HART |
| Operating Temperature | -40°C to +85°C |
| Ingress Protection | IP66, IP67 |
| Measured Medium | Liquids, gases |
Specifies qualifications and requirements for personnel working in hazardous areas.
Provides essential safety information for installing and mounting the device.
Lists crucial safety instructions related to connecting the device.
Provides instructions for connecting the device to the system.
Provides essential safety instructions for commissioning the device.
Details parameter assignment using the device display.
Enables Functional Safety for the device.
Details parameter assignment using remote operation tools.
Explains using sensor calibration to set the device characteristic curve.
Describes the safety function of the device and its use in safety instrumented functions.
Guides on enabling or disabling Functional Safety using a wizard.
Details enabling Functional Safety via the device display.
Guides on enabling Functional Safety using remote operation.
Describes performing proof tests to detect undetected errors.
Lists essential safety instructions for service and maintenance.
Lists important warnings and considerations for maintenance and repair.
Lists diagnostic message IDs, symbols, causes, and remedies.
Provides solutions for common device issues and error messages.
Details input specifications for gauge pressure, including measuring spans.
Specifies measuring accuracy details for SITRANS P320.
Specifies measuring accuracy details for SITRANS P420.
Documents validation of device data and safety-related parameters.
Documents validation of the safety function and date of validation.
Defined function executed by a safety-instrumented system.
Safety Integrity Level standard.
