Sony DCR-PC1 - Recording System Check; Preparation for Recording; IC1501(VFD) bist (REC) Check; IC1600(SFD) bist (REC) Check

5-42
• ENC Ya BIST Check
29) Select page: 3, address: 10, set data: 8C, and press the PAUSE
button of the adjustment remote commander.
30) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
31) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
32) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
33) When the playback system from IC1501 (VFD) to IC1402
(AOI) is normal, the display data (combination data) of page:
3, addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model PAL model
• ENC Ca BIST Check
34) Select page: 3, address: 10, set data: 8D, and press the PAUSE
button of the adjustment remote commander.
35) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
36) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
37) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
38) When the playback system from IC1501 (VFD) to IC1402
(AOI) is normal, the display data (combination data) of page:
3, addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model PAL model
• ENC Cb BIST Check
39) Select page: 3, address: 10, set data: 8E, and press the PAUSE
button of the adjustment remote commander.
40) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
41) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
42) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
43) When the playback system from IC1501 (VFD) to IC1402
(AOI) is normal, the display data (combination data) of page:
3, addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model PAL model
44) Select page: C, address: 51, set data: 03, and press the PAUSE
button of the adjustment remote commander.
45) Select page: 0, address: 01, and set data: 00.
B2
E7
DE
EE
Data Address
16
17
2. Recording System Check
2-1. Preparation for Recording
1) Playback the BIST check tape (XH5-6 (NTSC), XH5-6P (PAL)).
2) Select page: 3, address: 10, set data: C0, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 3, address: 11, set data: 07, and press the PAUSE
button of the adjustment remote commander.
4) Enter the STOP mode.
5) While keep the HOLD switch of the adjustment remote
commander at ON (SERVICE position), eject the BIST check
tape and insert a tape for recording in place of the tape.
6) Enter the camera recording mode.
Note: Perform all of the following checks in the camera record mode.
2-2. IC1501(VFD) BIST (REC) Check
1) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
2) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
4) When the recording system from IC1501 (VFD) to IC1600
(SFD) is normal, the display data (combination data) of page:
3, addresses: 14 and 15 agrees with any combination as shown
below.
NTSC model PAL model
2-3. IC1600(SFD) BIST (REC) Check
1) Select page: 0, address: 01, and set data: 01.
2) Select page: C, address: AC, set data: 21, and press the PAUSE
button of the adjustment remote commander.
3) Select page: C, address: AD, set data: 03, and press the PAUSE
button of the adjustment remote commander.
4) Select page: 3, address: 11, set data: 04, and press the PAUSE
button of the adjustment remote commander.
5) Select page: 3, address: 12, set data: 08, and press the PAUSE
button of the adjustment remote commander.
6) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
7) Select page: 3, address: 13, set data: 03, and press the PAUSE
button of the adjustment remote commander.
8) When the recording system from IC1600 (SFD) to IC1602 (LIP)
is normal, the display data (combination data) of page: 3,
addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model PAL model
9) When the recording system from IC1600 (SFD) to IC1601
(TDF) is normal, the display data (combination data) of page:
3, addresses: 18 and 19 agrees with any combination as shown
below.
NTSC model PAL model
Address
14
15
Data
D5
0B
00
15
BC
CE
Data Address
16
17
F7
F6
4F
69
Data Address
18
19
Address
16
17
Data
83
9E
FE
68
22
CA
Data Address
16
17
70
D5
43
E4
Data Address
16
17
ED
CB
9A
1E
Data Address
16
17
Address
16
17
Data
CC
ED
Address
14
15
Data
34
8A
2D
F5
A2
7B
Data Address
16
17
6C
C7
23
76
Data Address
18
19