Need help?Do you have a question about the Syn-Tech Systems FuelMaster Plus and is the answer not in the manual?
The FuelMaster® Site Operations Manual provides guidance for end users.
Introduces the FMU, system types (VMN, VVI, COM, EK, 2K, Keyless), and their basic functions.
Describes the manual's content, options, and organization into eight sections.
Briefly outlines the content of Sections II through VIII of the manual.
Details system types and configuration for Vehicle Key usage.
Explains the initial prompts displayed when using a Vehicle Key.
Guides through entering the Vehicle Key PIN and User ID.
Covers differences in User ID verification and odometer/chronometer input.
Details 'Odometer Too Low'/'Too High' errors, causes, and writing data back to the key.
Covers out-of-range odometer alerts, PM notifications, and oil check procedures.
Guides hose selection and explains dispenser status prompts.
Explains prompts related to pump handle status and operation.
Details User Key system types, configuration, and initial operation prompts.
Guides through User Key PIN, Vehicle ID, and Odometer/Chronometer input.
Covers odometer input, oil check, and hose selection for User Keys.
Explains dispenser status messages and pump handle prompts for User Keys.
Details configuration and initial operation prompts for Either Key systems.
Guides through PIN entry, User ID entry, and verification for Either Key system.
Details Odometer input, errors, and potential causes for Either Key system.
Covers re-entering odometer data and cancellation due to out-of-range entries.
Details PM alerts and ID/Odometer prompts for Either Key operations.
Covers oil check procedure and hose selection for both keys in this system.
Explains dispenser status and pump handle prompts for Either Key operations.
Details Two Key system configuration and initial operation prompts.
Guides through User Key PIN entry and confirmation of successful reading.
Explains Vehicle Key PIN entry and Odometer/Chronometer input for Two Key systems.
Covers odometer errors, re-insertion, and invalid key insertion errors.
Details PM alerts and hose selection for Two Key operations.
Covers dispenser status messages for Two Key operations.
Explains pump handle status prompts for Two Key operations.
Describes Manual Key use cases and prompts for VMN and other systems.
Covers ID validation, Chrono/Odometer input, and hose selection for Manual Keys.
Provides notes on hose selection and dispenser status for Manual Keys.
Explains pump handle status prompts for Manual Key operations.
Details Tanker Truck Key use, procedures, initial prompts, and PIN entry.
Guides hose selection, dispenser status, and handle prompts for Tanker Trucks.
Highlights differences for tanker truck keys on Mobile 2500 FMU.
Covers secure key handling, procedures, and presents the main menu options.
Lists main system menu options and details the Reports menu.
Describes ERR LOG and EVENTS report functions.
Details various report functions including ERR DUMP, LCD, REPRINT, CFG, and EIU CFG.
Provides options for credit card operations, including network configuration.
Details credit card print config and network menu options.
Covers credit card reader error and totalizer setting procedures.
Details CLOSEOUT, FLASH, and the Supervisor PM Menu.
Provides options to view and update Odometer/Chronometer information.
Presents options for programming, resetting, and setting AIM units.
Offers options to configure system time, date, and modify settings.
Details communication configuration: Baud Rate and Network Card settings.
Allows setting and changing pump totalizer values.
Accesses pump configuration: Menu and Initial settings.
Modifies settings for mechanical and electric pumps.
Configures electric pump address, blending, and AIM IDs.
Assigns system information like timers, durations, and digit counts.
Lists configurable system options like Key Type, Odom checks, and printer settings.
Provides access to various hardware tests: Switch, Outputs, LCD, Keypad, etc.
Tests unit's pump handle detection and relay board LEDs.
Tests LCD integrity, keypad, receipt printer, and detected boards.
Accesses ProKee® data display formats: FIELDS, ASCII, HEX, PIN.
Tests pulser count accuracy and FMU hardware integrity via reset.
Sets the FMU's time, date, and day of the week.
Provides options for manual fuel dispensing, hose mode, and service status.
Allows manual fueling and manages hose modes: Semi-Manual and Monitor.
Accesses options for setting pricing, shutting down, and re-enabling hoses.
Covers setting prices, shutting down, and re-enabling hoses.
Provides options for entering stick readings and adjusting tank quantities.
Covers entering stick readings, fuel drops, and tank quantity adjustments.
Lists common error prompts and initial troubleshooting steps.
Covers errors related to reading/writing keys and odometer calculation problems.
Details PM alerts, hose errors, and pump handle status problems.
Covers pump handle errors, configuration errors, and EEPROM issues.
Details errors related to tests, power, resources, and transaction memory.
Addresses FMU hardware failures like RAM battery or malfunction.
General| Brand | Syn-Tech Systems |
|---|---|
| Model | FuelMaster Plus |
| Category | Industrial Equipment |
| Language | English |
To Next Page
