Tektronix THS3024

Tektronix THS3024

130 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Introduction

16 THS3000 Series Oscilloscopes User Manual

Table of Contents

Table of Contents7
General Safety Summary12
Preface15
- Where to Find more Information16
- Terms Used in this Manual16
- Table I: Product Documentation16
Introduction17
- Product Description17
- Front Panel Navigation18
- Figure 1: Instrument Front Panel19
- Initial Setup25
- Restore Factory Default Settings28
- Figure 2: Rising Edge of Square Wave28
- Tilt Stand, Hanging Hook, and Kensington® Lock29
- Figure 3: Tilt Stand and Location of Kensington® Lock29
- Figure 4: How to Use the Hanging Hook Handle30
- Figure 5: How to Use the Hanging Strap Handle31
Operating Basics33
- Input Connections33
- Figure 6: Top Panel Input Connectors33
- About Floating Measurements34
- Figure 7: Isolated Input Architecture34
- Figure 8: Common-Reference Input Architecture35
- Connect Probes and Leads36
- Figure 9: Parasitic Capacitance between Probes, Instrument, and Environment37
- Figure 10: Parasitic Capacitance between Analog and Digital Reference38
- Figure 11: Correct Connection of Reference Leads38
- Figure 12: Wrong Connection of Reference Leads39
- Figure 13: Making Voltage Probe Connections on Four Channels40
- Figure 14: Voltage Probe Connection Using a Ground Spring41
- Figure 15: Connections Using Hook Tips and Alligator Clip Grounding42
- Figure 16: Probe Tip Ground Ring43
- Select an Input Channel44
- Adjust the Probe Type Settings45
- Display an Unknown Signal with Autoset or Autorange45
- Figure 17: Display with Autoset46
- Automatic Measurements47
- Figure 18: Display with Autorange47
- Figure 19: Hz and V Peak-Peak as Measurements49
- Stop the Display50
- Figure 20: Frozen (Stopped) Display50
- Average, Persistence, and Glitch Capture51
- Figure 21: Live (Running) Display51
- Table 1: Comparison of Averaged Versus Nonaveraged Waveforms52
- Figure 22: Using Persistence to Observe Dynamic Signals53
- Acquire Waveforms54
- Figure 23: FFT Measurement59
- Pass-Fail Testing62
- Table 2: Pixel Colors Description62
Recorder Functions63
- Plot Measurements over Time (Trendplot™)63
- Figure 24: RECORDER REPLAY Main Menu63
- Figure 25: Trendplot™ Measurement64
- Record Waveforms in Deep Memory (Scope Roll Mode)65
- Figure 26: Recording Waveforms Using Scope Roll Mode65
Analyze Waveforms68
- Use Replay68
- Use Zoom69
- Use Cursors70
- Figure 27: Zooming in on a Waveform70
- Figure 28: Voltage Measurement with Horizontal Cursors71
- Figure 29: Time Measurement with Vertical Cursors73
- Figure 30: Risetime Measurement Using Cursors75
Trigger Functions76
Table 3: Trigger Types77
Figure 31: Screen with All Trigger Information79
Figure 32: Trigger Delay or Pretrigger View80
Figure 33: Making a Single Shot Measurement83
Figure 34: N-Event Triggering84
Figure 35: Trigger on NTSC Video Signal Field 185
Figure 36: Pulse Width Triggering86
Table 4: Internal Memory87
Save and Recall87
Troubleshooting95
- Appendix A:specifications97
- General Speciﬁcations97
- Introduction97
- Table 5: Record Length (Samples/Points Per Input)97
- Table 6: Oscilloscope Inputs98
- Automatic Measurements102
- Table 7: Automatic Measurement Speciﬁcations102
- Recorder Speciﬁcations105
- Table 8: Recorder105
- Table 9: Zoom, Data Log, and Cursors105
- Zoom, Data Log, and Cursors Speciﬁcations105
- Miscellaneous Speciﬁcations106
- Table 10: Display106
- Table 11: Power106
- Table 12: Probe Calibration Output Signal107
- Table 13: Memory107
- Table 14: Interface Ports108
- Table 15: Mechanical108
- Table 16: Environmental108
- Safety Speciﬁcations109
- Table 17: Safety Speciﬁcations109
- Figure 37: Input Voltage Versus Frequency110
- Figure 38: Maximum Voltage between Oscilloscope References, and between Oscilloscope References and110
- Probe Speciﬁcations111
- Table 18: THP0301 Voltage Probe111
Appendix A: Speciﬁcations97
Appendix B: Connect the Instrument to a Computer113
- USB Ports114
- Install USB Drivers115
- Conﬁrm Oscilloscope and PC Communication116
Appendix C: Probe Compensation and Compatible Maximum Voltages119
- Compensate Voltage Probes119
- Compatible Probe Maximum Voltages121
- Table 19: Compatible Probe Maximum Voltages121
Appendix D: Battery Pack123
- Save Battery Life123
- Charge the Batteries124
Appendix E: Maintenance and Cleaning127
- Maintaining the Instrument127
- Cleaning127
- Storage127
Index129

Related product manuals

Preview: Tektronix TekScope THS710A

Tektronix TekScope THS710A

Preview: Tektronix THDP0100

Tektronix THDP0100

Tektronix TDS2014

Tektronix TDS2012

Tektronix TDS2024

Tektronix TDS1012

Tektronix TDS 360

Tektronix TDS1002

Tektronix TDS3012

Tektronix TDS2002